All guides
viewhub.stream · How-to Guides

LCD Video Walls

Choose panels, plan the layout, mount and align, connect the signal and calibrate the wall

6 min readUpdated

Contents

Before you start

An LCD video wall joins several flat-panel displays into one large screen. Compared with LED, LCD walls give very high resolution at close viewing distances for less money, which makes them popular for control rooms, reception areas, retail and meeting spaces. Their weak point is the thin black frame (bezel) around each panel. This guide covers choosing panels, planning the layout and resolution, mounting and aligning them, connecting and processing the signal, and calibrating the wall so it looks like one screen.

LCD video wallLED video wall
SeamsVisible bezel lines between panelsSeamless
Resolution at close rangeVery high (each panel is usually Full HD or 4K)Needs a fine, expensive pitch
BrightnessTypically 500 to 700 nits; high-brightness panels for windowsMuch higher, suitable for outdoors
Size and shapeFixed by the panel size, usually 46 or 55 inch panelsAny size in whole cabinets
Cost for close viewingLowerHigher

Choose the panels

  • Use dedicated video wall panels, not televisions or standard signage displays. They have ultra-narrow bezels, are built for long running hours, and include features for walls: daisy-chaining, bezel compensation, tiling settings and colour calibration.
  • Bezel width is quoted as the bezel-to-bezel gap between two panels' pictures, from about 0.4 mm on premium panels to 3.5 mm on budget ones. Narrower bezels cost more but are far less noticeable, especially for text and fine detail crossing the seams.
  • Brightness: 500 nits suits most indoor spaces; 700 nits or more for bright foyers; high-brightness panels (2,500 nits and above) for shop windows.
  • Running hours: choose panels rated for 24/7 use if the wall runs continuously.
  • Buy all panels at once, from the same production batch, so their colour and brightness match. Order a spare or two at the same time.

Plan the layout and resolution

Walls are described by columns × rows: a 3 × 3 wall of 55-inch panels is about 3.6 m wide and 2 m high.

  • Resolution is each panel's resolution multiplied by the columns and rows. A 3 × 3 wall of Full HD panels is 5,760 × 3,240 pixels.
  • Bezels hide pixels if bezel compensation is used (see below), so the content should allow for the bezels.
  • Avoid a seam at eye level or through the middle of a person's face in a presenter-heavy setting. An odd number of rows or columns puts a panel, not a seam, in the centre.
  • Portrait walls are possible, but check which way the manufacturer requires the panels to be rotated, as panels are designed to be turned in one direction only for cooling.
  • Viewing distance: walls look best from at least 1.5 to 2 times the wall's height away, where the bezels become less noticeable.

The LCD Video Wall Calculator works out size, resolution, bezel compensation, weight and power, and the Display Size Converter converts diagonal sizes to width and height.

Bezel compensation

Without compensation, the picture is split evenly across the panels, and the bezels sit on top of it like window frames. Straight lines crossing a seam look broken. Bezel compensation treats the bezel as part of the picture, hiding the pixels that would be "behind" it, so lines continue straight across the seams.

A diagonal line crossing a bezel, without and with bezel compensation Without compensationWith compensation
Without compensation, a diagonal line drops at the seam: the dashed line shows where it should be. With compensation, the pixels "behind" the bezel are hidden, so the line stays straight.
  • Use compensation for images, video and graphics that cross the seams, so they look natural.
  • Turn it off, or design around the seams, for data and text content where nothing should be hidden. Many control room layouts place separate windows on each panel instead.
  • Compensation is set in the panels' tiling settings or the video wall processor.

Mount and align

  1. Check the wall can carry the weight, and plan fixings with a structural assessment where needed. A 55-inch video wall panel weighs about 20 to 30 kg.
  2. Use a dedicated video wall mount with micro-adjustment in all directions and push-to-release (pop-out) arms, so panels can be pulled forward for servicing without removing them.
  3. Set out the wall from a level baseline and centre line with a laser level. Install the bottom row first, from the centre outwards.
  4. Align carefully: adjust each panel so the seams are straight and even, and the faces are flush. Use the alignment spacers supplied, and never let panels press against each other, which can stress the glass.
  5. Leave ventilation space around and behind the panels as the manufacturer specifies, especially in recesses. Heat shortens panel life and causes colour drift.
  6. Plan the cabling behind the wall before mounting, with power and signal cables neatly managed and enough slack to pull panels forward.

Connect and process the signal

Options

MethodHow it worksBest for
Daisy chain with built-in scalerOne source feeds the first panel; each panel passes the signal on (via DisplayPort or HDMI loop-out) and shows its own partSimple walls showing one source. Resolution is limited to the input, often Full HD or 4K across the whole wall
Video wall processor or controllerA processor takes several sources and sends a separate output to each panelHigh resolution, multiple sources and windows, control rooms
Signage player with video wall supportEach panel has its own player, synchronised over the network, or one player outputs to several panelsSignage content at full resolution
AV over IPEncoders and decoders on a network, with each decoder feeding a panelLarge or distributed systems needing flexible routing

Daisy chain set-up

  1. Connect the source to the first panel and daisy-chain from each panel's output to the next, following the manufacturer's limit on the number of panels and resolution.
  2. Give every panel a unique ID, usually by remote control or through the control software.
  3. In each panel's tiling (video wall) settings, set the number of columns and rows and its position.
  4. Turn bezel compensation on or off and set the bezel size.

Control

Most video wall panels can be controlled over RS-232 or the network, for power scheduling, input switching and monitoring. Use the manufacturer's software or a control system to switch the whole wall on and off together, rather than panel by panel.

Calibrate the wall

Even panels from the same batch differ slightly. Calibration makes them look like one screen.

  1. Warm up the wall for at least 30 minutes before calibrating.
  2. Set every panel to the same picture mode and settings, with dynamic contrast, energy saving and ambient light sensors switched off unless they are used across the whole wall.
  3. Use the manufacturer's calibration tool with a colorimeter where available. It measures each panel and adjusts its colour and brightness to a common target.
  4. Otherwise, adjust by eye using full-white and mid-grey test patterns, matching each panel's brightness and colour to a reference panel near the centre.
  5. Re-check after a few weeks, then periodically, as panels age at slightly different rates.

Content and care

  • Design content at the wall's full resolution, with the bezels in mind: keep important text and faces away from seams.
  • Avoid static images for long periods. LCD panels can suffer image retention from static logos, tickers and interfaces. Use the panels' pixel shift or screen-saver features, move static elements occasionally, and schedule the wall off out of hours.
  • Clean with the power off, using a dry microfibre cloth or one lightly dampened with water, wiping gently. Never spray liquid onto the panels.
  • Keep spares from the same batch, and record panel serial numbers, IDs and settings.

Troubleshooting

ProblemLikely causesThings to try
Panels show the wrong part of the pictureWrong IDs or tiling positionsCheck each panel's ID and position in the tiling settings.
Panels after a certain point show no signalDaisy-chain cable fault, chain too long, HDCP or resolution limitsCheck the cable into the first blank panel, and the manufacturer's chain limits.
One panel brighter or a different colourDifferent settings, energy saving active, panel ageing or from a different batchMatch the settings, turn off energy saving, recalibrate.
Uneven seamsMount not alignedUse the mount's micro-adjustment to realign.
Ghost image of a logoImage retention from static contentRun the panels' retention-removal feature and vary the content.
Back to top