All guides
viewhub.stream · How-to Guides

Subwoofers: Sizing, Placement and Arrays

How many subwoofers you need, where to put them in a room, and how to arrange, mount and align them, including cardioid and back-to-back set-ups

10 min readUpdated

Contents

Before you start

Subwoofers reproduce the deepest bass, below about 80 to 120 Hz, which most speakers cannot produce at a useful level. Good bass is felt as much as heard and gives music its weight, but it is also the hardest part of the sound to get right. Low frequencies have long wavelengths, spread in all directions, interact strongly with rooms, and cancel or add up depending on where you stand. This guide covers how many subwoofers you need, where to put them in a room or at an event, how to connect and align them, and the main ways of arranging them, including cardioid set-ups with back-to-back cabinets.

Why bass behaves differently

A 50 Hz bass note has a wavelength of about 6.9 m; at 100 Hz it is about 3.4 m. Because the wavelengths are as large as the room, or larger, bass is not aimed like treble. It spreads around the cabinet, reflects off walls and floors, and builds up or cancels in different places. Positioning, the number of subwoofers and the timing between them matter far more than in the rest of the system.

How many subwoofers?

  1. Decide the bass level you need at the listening position. For background music, gentle support is enough. For live bands and DJs, the bass is often 6 to 10 dB above the rest of the mix.
  2. Check one subwoofer's maximum output (maximum SPL at 1 m) and subtract the loss with distance: about 6 dB per doubling of distance outdoors, less indoors where the room supports the bass.
  3. Add subwoofers to make up the difference. When identical subwoofers are placed close together and fed the same signal, their outputs add up efficiently in the bass: each doubling of the number of subwoofers gives up to 6 dB more maximum level (3 dB from twice the power, plus 3 dB from the cabinets coupling together).
  4. Use the boundaries. Placing a subwoofer on the floor, against a wall or in a corner raises its output in the room (see below).
  5. Allow headroom: do not plan to run subwoofers at their limit. A few dB of spare level keeps the bass clean and protects the drivers.
Number of subwoofers (coupled)Extra maximum level
1Reference
2Up to +6 dB
4Up to +12 dB
8Up to +18 dB

As a rough guide for live music, many systems use about one subwoofer of a similar size for each full-range box, or more for bass-heavy music. Use the manufacturer's prediction software for large systems. The Speaker Coverage & SPL Calculator and dB Toolbox help with the level calculations.

Driver size

  • 8 to 10 inch: compact subwoofers for installations, background music and small rooms.
  • 12 inch: portable PA, bars and small venues.
  • 15 and 18 inch: live sound and clubs; 18 inch drivers move the most air and reach lowest.
  • Dual-driver cabinets (2 × 15 or 2 × 18 inch) for high output in less floor space.

Boundaries and room placement

Bass that would spread in all directions is reflected back by nearby surfaces. Each large surface close to a subwoofer, compared with the wavelength, concentrates its output into a smaller space:

PositionTheoretical gain at low frequencies
In free space (flown, away from surfaces)Reference
On the floorUp to +6 dB
On the floor against a wallUp to +12 dB
In a corner on the floorUp to +18 dB

In practice the gains are smaller, but placing subwoofers on the floor and near walls is an efficient way to get more bass from fewer cabinets. The catch is that corners also excite the room's resonances most strongly, which can make the bass boomy and uneven.

Room modes

In an enclosed room, bass reflects back and forth between parallel walls, floor and ceiling. At certain frequencies the reflections reinforce each other, producing room modes: some notes boom, others nearly disappear, and the effect changes from seat to seat. The lowest mode along each dimension is at:

frequency = 343 ÷ (2 × length in metres)

A room 10 m long has its first lengthways mode at about 17 Hz, with further modes at 34, 51, 69 Hz and so on. Small rooms have widely spaced modes in the range subwoofers play, which makes bass very uneven.

Pressure of the first two room modes along the length of a room, and good subwoofer positions Loud at the end wallsFirst mode silent halfwayFirst mode (343 ÷ 2L)Second mode (twice the frequency)Subwoofers (blue) on opposite end walls cancel the first mode
Bass pressure of the first two lengthways modes. Both are loudest at the end walls. A subwoofer halfway along the room sits where the first mode is silent, so it does not excite it, and two subwoofers on opposite end walls cancel it. That is one reason multiple subwoofers give smoother bass.

Placement in rooms

  • Multiple subwoofers smooth the bass. Two subwoofers at the midpoints of opposite walls, or four at the midpoints of all four walls, give much more even bass across the seating than one in a corner, because each excites the room modes differently and their peaks and dips partly cancel.
  • The subwoofer crawl for a single subwoofer: put the subwoofer at the main listening position, play bass-heavy music or a low-frequency sweep, then move around the room at floor level listening for the place where the bass sounds smoothest and fullest. Put the subwoofer there.
  • Measure with a measurement microphone and analyser at several seats, and compare positions. Small moves of a metre can make a big difference.
  • Avoid the exact centre of the room and equal distances from two walls, which line up the modes and make peaks and dips worse.
  • Keep the subwoofer near the main speakers where possible, so the bass and the rest of the sound arrive together and seem to come from the same place.

Subwoofer arrays for live sound

At events and in venues, how the subwoofers are arranged decides how even the bass is across the audience and how much goes onto the stage.

Four subwoofer arrangements seen from above: left and right stacks, centre cluster, end-fire and cardioid StageLeft and right stackspower alley in the middle, gaps either sidepower alleydipsdipsStageCentre or broadsideeven bass across the widthStageEnd-firein line, front cabinets delayed0 ms… delayedmost delay at the frontless on stageStageCardioid (back to back)rear cabinet reversed, inverted and delayedrear-facingforward-facingforward bass
Top views. Left and right stacks create a "power alley" and gaps; a centre cluster gives even bass across the width; end-fire and cardioid arrays send the bass forwards and reduce it on stage.

Left and right stacks

The most common set-up: subwoofers stacked under or beside the main speakers on each side of the stage. Because the two stacks are several metres apart, their bass adds up strongly on the centre line (the "power alley") and cancels in places either side, giving uneven bass across the audience. Fine for small events; for larger ones, consider a centre or broadside array.

Centre cluster and broadside arrays

  • Centre cluster: all the subwoofers together in the middle, under the stage front or flown centrally. Acts as one source, giving even bass across the width.
  • Broadside array: subwoofers spread in a line across the stage front. Keep the gaps between cabinets less than about half a wavelength at the crossover frequency (about 1.7 m at 100 Hz) so they combine smoothly, or the coverage breaks up.
  • Arc or delay-shaped arrays: a straight line of subwoofers beams the bass narrowly forward. Placing them in a curve, or adding small delays to the outer cabinets, widens the coverage to suit the audience area.

End-fire arrays

Two or more subwoofers placed one behind the other, all facing forwards, spaced about a quarter of a wavelength apart at the main frequency of interest (about 0.85 m at 100 Hz). Each cabinet further forward is delayed by the time sound takes to travel from the rearmost cabinet:

delay (ms) = distance from the rearmost subwoofer (m) ÷ 343 × 1,000

In front, the sound from every cabinet arrives together and adds up. Behind, it arrives at different times and partly cancels, reducing bass on the stage. End-fire arrays need depth on the floor, so they suit the front of a stage or the ends of a field.

Cardioid arrays and back-to-back subwoofers

A cardioid subwoofer array sends bass forwards and cancels it behind, typically by 15 dB or more at the rear. The usual way uses one or more cabinets facing backwards:

  1. Arrange the cabinets: for example a stack of three with the middle one facing the rear, or pairs placed back to back, or a rear-facing cabinet directly behind front-facing ones. Common ratios are two or three forward-facing cabinets for every rear-facing one.
  2. Invert the polarity of the rear-facing cabinet, so its sound behind the array is opposite to the sound arriving from the front-facing cabinets.
  3. Delay the rear-facing cabinet by the time sound takes to travel from the front cabinets' drivers to the rear cabinet's drivers: distance (m) ÷ 343 × 1,000 ms. For cabinets back to back with drivers 0.8 m apart, that is about 2.3 ms.
  4. Measure behind and in front, and fine-tune the delay and level of the rear-facing cabinet until the rear cancellation is deepest while the front stays strong. Many manufacturers publish exact presets for their cabinets, which take into account the cabinet's own response.

Back to back without processing is not cardioid. Two subwoofers placed back to back, both fed the same signal with no polarity change or delay, simply give a little more output in all directions, including onto the stage. The rear-facing cabinet only cancels the rear sound when its polarity and delay are set correctly.

Cardioid arrays are worth the effort where bass on stage is a problem: in front of performers, near microphones, in reverberant rooms, or where bass must be kept away from a back wall or neighbours behind the stage.

Flown subwoofers

Flying subwoofers next to or behind a line array gives more even bass from the front rows to the back, and keeps the front rows from being overwhelmed. Flown subwoofers lose the floor's boundary gain, so more cabinets are needed for the same level, and they need rated rigging points. Many systems combine flown and ground subwoofers.

Mounting and installing subwoofers

  • On the floor: the simplest and most efficient for bass. Use isolation feet or pads on hollow stages and floors to reduce rattles.
  • Under the stage or seating: hidden subwoofers firing through an opening. Make sure the opening is large enough and the space does not resonate.
  • In ceilings and walls: installation subwoofers designed for ceiling voids or wall cavities, in back boxes. Keep them clear of loose tiles, light fittings and ductwork that can rattle.
  • Furniture and bench subwoofers: built into banquettes or cabinetry in bars and restaurants. Effective, but the furniture must be rigid and isolated, or it will buzz.
  • Flown or wall-mounted: only with the manufacturer's approved brackets and rigging hardware, fixed to suitable structure, with secondary safety.
  • Isolation from the building: in shared buildings, bass travels through the structure into neighbouring rooms and flats. Use isolation mounts and keep subwoofers off party walls and floors over neighbours.

Connect and align

  1. Set the crossover: send frequencies below about 80 to 120 Hz to the subwoofers and above that to the main speakers, using the processor's or the speaker's crossover. Use the manufacturer's recommended settings where available.
  2. Add a high-pass (infrasonic) filter on the subwoofers, around 25 to 35 Hz, to stop them wasting power on frequencies they cannot reproduce and to protect the drivers. Many processors and powered subwoofers include this.
  3. Check polarity: with the main speakers and subwoofer playing together, flip the subwoofer's polarity. The setting with more bass around the crossover frequency is usually correct.
  4. Time-align the subwoofers with the main speakers, using delay or phase controls, so their sound arrives together at the main listening area. The Subwoofer Alignment Calculator and Speaker Delay Time Calculator help; measuring is best.
  5. Set the level by ear and measurement, so the bass is full but not boomy, and blends with the main speakers.
  6. Use a limiter to protect the subwoofers, set to the manufacturer's recommendations.
  7. EQ gently: cut room-mode peaks with narrow filters if needed, but do not boost dips; they are cancellations and boosting wastes power.

Feed subwoofers from an auxiliary send at live events, rather than the main mix, so only the instruments that need deep bass (kick drum, bass, keyboards, playback) go to the subwoofers. Vocals and microphones then stay clean and less prone to low-frequency rumble and feedback.

Troubleshooting

ProblemLikely causesThings to try
Boomy bass on certain notesRoom modes, subwoofer in a corner, too much levelMove the subwoofer, add a second one at the opposite wall, cut the peak with EQ, lower the level.
Bass strong in some seats, weak in othersRoom modes, left and right stacks creating a power alleyUse multiple subwoofers in symmetrical positions, or a centre or broadside array.
Thin bass at the main listening areaSubwoofer out of polarity or time with the main speakersCheck polarity and alignment, and measure.
Too much bass on stageOmnidirectional subwoofers close to the stageUse a cardioid or end-fire array, or move the subwoofers.
Rattles and buzzesLoose fixings, ceiling tiles, furniture or stage panelsPlay a slow low-frequency sweep, find the rattle and fix or isolate it.
Subwoofer distorts or limits earlyNot enough subwoofers, no high-pass filter, playing frequencies below its rangeAdd the infrasonic filter, add subwoofers, lower the level.
Complaints from neighboursBass travelling through the structureIsolate the subwoofers from the building, move them away from shared walls, use cardioid arrays, and limit the level.
Back to top