All guides
viewhub.stream · How-to Guides

Wireless Microphones: Frequencies, Antennas and Reliable Set-Up

Plan UK frequencies, place antennas, set up and fit transmitters, and stop dropouts and interference

11 min readUpdated

Contents

Before you start

Wireless microphones free presenters and performers from cables, but they add a radio link that can drop out, pick up interference or simply run out of battery at the worst moment. Almost every wireless problem comes down to the same few things: the wrong frequencies, poor antenna placement, flat batteries or bodies and metal in the way. This guide covers how to plan, set up and run wireless microphones and in-ear monitors reliably in the UK, from a single handheld in a meeting room to a stage full of radio mics.

  1. Choose the right system and frequency band for the job.
  2. Plan the frequencies so the systems do not interfere with each other or anything else.
  3. Place the antennas for a clean line of sight to the transmitters.
  4. Set up each system: sync, gain, labels and batteries.
  5. Fit the transmitters on people properly.
  6. Walk test the whole area, then monitor the systems during the event.

How a wireless system works

Each transmitter (a handheld microphone, or a bodypack with a lavalier or headset) sends audio on one radio frequency to its own receiver, which connects to the mixer like any other microphone. Every transmitter needs its own frequency: two on the same frequency interfere and both become unusable. Most professional receivers use diversity, with two antennas a short distance apart. When the signal fades on one antenna, as it does when radio waves bounce off walls and cancel out, the receiver switches to the other.

Choose the system

TypeGood forThings to know
UHF analogueMost live and installed useLong range and proven. Needs careful frequency planning when many systems run together.
UHF digitalLarger systems, theatre, touringClean audio with no companding artefacts, and usually more channels fit in the same space. Adds a few milliseconds of latency.
2.4 GHz digitalSmall rooms, schools, small venues, quick set-upsLicence-exempt worldwide and easy, but shares the band with Wi-Fi and Bluetooth, so channel count and range are limited in busy buildings.
1.9 GHz (DECT band)Meeting rooms, conferences, lecture theatresLicence-exempt with automatic frequency management. Good for speech; fewer channels than UHF.
VHFSimple, low-cost single systemsFew channels and larger antennas. Fine for one or two microphones.

Microphone style

  • Handheld: for presenters who are used to holding a microphone, Q&A, and singers. Gives the most gain before feedback.
  • Headset: hands-free with the microphone close to the mouth. The best choice for presenters who move around, theatre, fitness instructors and anyone quiet.
  • Lavalier (lapel): discreet, for television, interviews and presenters who will not wear a headset. Sits further from the mouth, so it feeds back sooner in loud rooms.
  • Instrument packs: for guitars, basses and other instruments with a jack output.

Frequencies and licences in the UK

Radio microphones must only use frequencies allowed in the UK, which Ofcom manages. Each system is built to tune within a particular range, printed on the receiver label (for example "606–614 MHz" or "823–832 MHz"), so check the range before you buy or hire.

BandLicenceTypical number of systemsNotes
Channel 38: 606 to 614 MHzShared Ofcom licence (UK Wireless Microphone Licence)Around 10 to 12The main band for professional UHF in the UK. The licence is inexpensive and shared, so holders coordinate between themselves.
Interleaved spectrum: 470 to 606 and 614 to 694 MHzCoordinated licence for a specific site and dateMany, depending on locationGaps between TV transmitters. Used by theatres, broadcasters and large events, booked through Ofcom's PMSE licensing.
823 to 832 MHzMoved to licence-exempt in 2026SeveralThe "duplex gap" between mobile phone bands. Check Ofcom's current rules before relying on it.
863 to 865 MHzLicence-exemptAbout 4Low power and crowded. Fine for a few systems.
1785 to 1805 MHzMoved to licence-exempt in 2026SeveralUsed by some digital systems. Check Ofcom's current rules.
1880 to 1900 MHz (DECT)Licence-exemptVaries by systemConference and speech systems with automatic frequency management.
2.4 GHzLicence-exemptLimited by Wi-Fi activityShared with Wi-Fi and Bluetooth.

Old equipment may be illegal to use. Systems in Channel 69 (854 to 862 MHz) and the 790 to 862 MHz range were cleared for mobile phone networks and can no longer be used. Many imported systems tune to frequencies used by mobile networks or TV in the UK. Using them is illegal and they will suffer interference. If in doubt, check the receiver's frequency range against Ofcom's current guidance.

Ofcom reviews these bands from time to time, so check its website for the latest information on licence-exempt bands, the shared Channel 38 licence and coordinated licences.

Plan the frequencies

Choosing frequencies is about more than avoiding duplicates. When several transmitters are on at once, their signals mix inside receivers and create extra, unwanted frequencies called intermodulation products. If one of these lands on another system's frequency, that system gets noise or dropouts even though nobody else is using its frequency.

Two transmitters creating third-order intermodulation products either side 604606608610612614616Frequency (MHz)f1f22f1 − f22f2 − f1TransmittersIntermodIntermod
Two transmitters at f1 and f2 create third-order products at 2f1 − f2 and 2f2 − f1, the same spacing again either side. No other system should use those frequencies.

How to choose frequencies

  1. Use the manufacturer's frequency groups. Every professional system has preset groups of frequencies already calculated to be free of intermodulation with each other. Put all systems of the same model in the same group, using a different channel for each.
  2. Scan first. Switch on all the receivers with their transmitters off and run the scan (group scan on most systems) to find which channels are clear at this venue. Run it with the venue's own equipment, lighting and LED screens switched on, because they all produce radio noise.
  3. Use coordination software for larger systems or mixed brands. Shure Wireless Workbench, Sennheiser's planning tools and similar programs calculate compatible frequencies across many systems, taking scan data into account.
  4. Keep in-ear monitors apart. IEM transmitters are much more powerful than microphone transmitters. Put them in a separate part of the band from the microphones, and their antennas well away from the microphone receivers' antennas.
  5. Record the plan: system, name, frequency, group and channel, and keep a few clear frequencies in reserve for problems on the day.

Ask what else is in the building. Theatres, conference centres and churches often have their own radio mics, assistive listening systems or neighbours using the same band. Contact the venue before the event so plans can be shared.

Place the antennas

Most dropouts are caused by antennas, not by the transmitters. Radio signals at these frequencies are absorbed by people, blocked by metal and reflected by walls, so the receiver antennas need a clear view of the area where the transmitters will be used.

Good and poor receiver antenna placement relative to a stage Stage: transmitters used here Antenna: front of stage,raised, clear line of sight Second antenna, a fewmetres away for diversity Rack at back Not here: behind the audience,inside a metal rack, far from the stage
Put antennas where they can see the stage, not inside racks or behind people. If the receivers live in a rack at the back, use remote antennas at the front.
  • Line of sight. Each receiver antenna should be able to "see" every place a transmitter will be. A crowd of people between them can cut the signal dramatically.
  • Get them up. Mount antennas above head height, 2 to 3 m up, so the signal passes over the audience.
  • Keep them close. The nearer the antennas are to the transmitters, the stronger and more reliable the signal. Use remote antennas on stands at the front of the room rather than relying on the antennas on the back of a receiver in a rack.
  • Keep clear of metal and noise. Mount antennas at least a metre from metal structures, LED screens, lighting dimmers, Wi-Fi access points and computers.
  • Space diversity antennas apart by at least a quarter of a wavelength (about 12 cm at 600 MHz) and preferably a metre or more.
  • Use antenna distribution for more than two receivers: one pair of antennas feeds a distribution amplifier, which splits the signal to every receiver. It saves a forest of antennas and improves reliability.
  • Use the right cable. Antenna cable loses signal over distance. Use low-loss 50 Ω coaxial cable for runs over a few metres, and keep runs as short as possible. Only use in-line boosters where the manufacturer recommends them, to make up for known cable loss.
  • Directional (paddle) antennas focus on the stage and reject signals from other directions, which helps in large or busy venues. Point them at the middle of the performance area.

Set up each system

  1. Set the receiver frequency from your plan, or using the group scan.
  2. Sync the transmitter to the receiver, usually by infrared or a sync button. Check both show the same frequency.
  3. Fit fresh batteries, or fully charged rechargeables (see below).
  4. Set the transmitter gain (sensitivity) so the loudest speech or singing just avoids the peak indicator on the receiver's audio meter. Headsets close to the mouth usually need less gain than lavaliers.
  5. Set the receiver output to match the mixer input (mic level is usual), then set the mixer gain as for any wired microphone.
  6. Set the transmitter power if it is adjustable. Low power (around 10 mW) is plenty in most rooms and reduces intermodulation; use higher power only for large venues or long distances.
  7. Name and label each system on the receiver and the transmitter ("Lectern", "Host", "Guitar"), with matching coloured tape or ID rings.
  8. Lock the transmitters and receivers so nobody can change the frequency or gain by accident.

Batteries

  • Use new alkaline batteries for every show or rehearsal, or the system's own rechargeable packs, fully charged. Never trust a part-used battery for an important event.
  • Know how long each system runs on a fresh battery, and change batteries at a planned time rather than waiting for the warning.
  • Battery meters on rechargeable packs are accurate; meters on alkaline batteries are only a rough guide, and some rechargeable AA cells show "low" while still having plenty left.
  • Keep a labelled box of fresh batteries and a separate one for used ones, so they never get mixed up.

Fit transmitters on people

  • Bodypacks go on a belt or waistband, or in a pouch, with the antenna hanging free and clear of the body. Do not coil the antenna, tuck it into a pocket against the skin or let it touch metal.
  • Headsets: microphone 1 to 3 cm from the corner of the mouth, out of the breath path. Run the cable behind the ear and down the back, taped if needed, with a little slack so turning the head does not pull it.
  • Lavaliers: centre of the chest, about a hand's width below the chin, clear of jewellery, ties and lanyards. Use a clip or tape so it does not rub on clothing, which is the most common source of noise.
  • Handhelds: hold the body, not the grille, and not over the antenna at the bottom of the microphone, which blocks the signal.
  • Brief the person: where the mute switch is, to keep it unmuted on stage, and that the microphone is live everywhere, including backstage and in the toilets. The engineer should keep the fader down until they are on.
  • Hygiene: clean headset and handheld microphones between users, and use disposable covers or windshields for headsets.

Walk test and monitor

  1. Walk test every system before the audience arrives, with all the other systems, IEMs, lighting and screens switched on. Walk the whole performance area and anywhere a presenter might go, including the edges of the stage, the audience aisles and backstage, while someone listens on headphones and watches the receiver's signal meters.
  2. Watch the RF and diversity indicators. Both antennas should show strong signal across the area. Places where the signal drops sharply need an antenna moved, not a change of frequency.
  3. Listen for noise with each transmitter switched off: a receiver showing signal with its transmitter off has found interference, so change its frequency.
  4. Monitor during the event using the receivers' front panels or the manufacturer's software, which shows signal strength, audio level and battery life for every system on one screen.
  5. Keep spares ready: a spare handheld on a clear frequency, set up and tested, saves the day when a transmitter fails.

In-ear monitors

Wireless in-ear monitor (IEM) systems work the other way round: a transmitter at the mixer sends a monitor mix to a bodypack receiver worn by the performer.

  • Plan IEM frequencies with the microphones, in a separate part of the band, because IEM transmitters are much stronger.
  • Keep IEM transmitter antennas at least a few metres from microphone receiver antennas, and do not combine them on the same antenna system.
  • Use a combiner to feed several IEM transmitters from one antenna; it reduces intermodulation and clutter.
  • Start with the bodypack volume low before the performer puts the earpieces in, and use a limiter on every IEM mix to protect hearing.
  • Good-fitting earpieces (ideally custom-moulded) seal out stage noise, so the mix can be quieter and safer.

Troubleshooting

ProblemLikely causesThings to try
Dropouts in certain placesAntenna placement, body or metal blocking the signal, antennas too far awayMove antennas closer with a clear line of sight, raise them, use remote or directional antennas, and check the bodypack antenna is not coiled or against the skin.
Noise or crackle with good signalInterference or intermodulation, a faulty microphone cable or connectorRescan and change frequency, check the frequency plan, and swap the headset or lavalier.
Signal showing with the transmitter offInterference on that frequencyChange to a clear frequency from the same group.
Rustling or clothing noiseLavalier rubbing on clothing or jewelleryRe-fit the microphone with tape or a clip, away from fabric and jewellery.
Distortion on loud voicesTransmitter gain too highLower the transmitter gain, then make it up at the mixer.
Quiet or thin soundTransmitter gain too low, headset or lavalier too far from the mouthRaise the transmitter gain, re-position the microphone.
Short battery lifeOld or low-quality batteries, high transmitter powerUse fresh batteries or charged packs, and lower the power if it is adjustable.
Receiver will not syncDifferent frequency bands, transmitter lockedCheck both units are the same band, and unlock the transmitter.
Back to top