All guides
viewhub.stream · How-to Guides

How to Set Up a Digital Mixer

Patch inputs and outputs, organise channels, build monitor mixes and effects, and use scenes safely on any digital desk

11 min readUpdated

Contents

Before you start

A digital mixer can do far more than an analogue desk of the same size: processing on every channel, built-in effects, flexible routing, scenes that recall every setting, remote control from a tablet and recording over USB or a network. That flexibility is also what makes a new digital desk feel confusing. Nothing is fixed: inputs, channels, buses and outputs are all connected in software, so you have to tell the desk what goes where.

This guide explains how to set up any digital mixer from scratch. It uses general terms that apply across the common ranges, such as Allen & Heath, Yamaha, Behringer and Midas, Soundcraft and others. Each brand uses slightly different names, so the main alternatives are given.

  1. Plan the inputs and outputs on paper.
  2. Start from a clean show and set the basics: sample rate, clock and network.
  3. Patch the physical sockets to channels and outputs.
  4. Name, colour and arrange channels so the desk is easy to use.
  5. Set up processing, buses, effects and monitor mixes.
  6. Build scenes, protect what must not change, and save the show file.

Key ideas

Sockets are not channels

On an analogue mixer, socket 1 is channel 1. On a digital mixer, the physical sockets (on the desk, a stage box or a network) are just sources. Patching connects them to channels, and channels to outputs, in software. Any socket can feed any channel, and one socket can feed several channels.

Input patching from sockets to channels, and output patching from buses to sockets Stage box 1Stage box 2Stage box 3Desk input 1Laptop (USB)Ch 1 LecternCh 2 Host RFCh 3 Panel 1Ch 9 Laptop L/RCh 12 AudienceMain L/RMain speakersMix 1Wedge 1Matrix 1StreamMatrix 2Hearing loopSocketsChannelsMixes to outputs
Input patching assigns sockets to channels; output patching assigns mixes to physical outputs. Neither has to be in numerical order.

The parts of a digital mixer

PartAlso calledWhat it does
Input channelsChannels, inputsProcess one source each: gain, filters, EQ, dynamics, sends and fader.
Stereo inputs, FX returnsST in, returnsChannels for stereo playback and effects, often with simpler processing.
Mix busesAuxes, mixesSeparate mixes for monitors, effects, recording or other rooms.
GroupsSubgroups, busesCombine several channels into one fader with its own processing, then into the main mix.
Main mixLR, master, stereo, mainsThe main audience mix.
MatrixMatricesOutputs built from the main mix and buses, for delay speakers, other rooms, streams and hearing loops.
DCAsVCAsControl faders that move the level of several channels at once without mixing them.
Mute groupsMute mastersMute or unmute many channels with one button.
Layers and banksFader layers, pagesWhich channels appear on the physical faders at a time.
ScenesSnapshots, cues, presetsSaved sets of settings that can be recalled.
Show fileShow, sessionEverything on the desk: patching, names, settings and all scenes.

Plan the inputs and outputs

Ten minutes with a spreadsheet saves an hour at the desk. Make three lists:

  • Input list: channel number, name, source (microphone, DI, playback), socket (desk, stage box, network), phantom power yes or no, and stand or position.
  • Output list: every mix and where it goes: main speakers, subwoofers, front fills, each monitor wedge or in-ear mix, recording, stream, hearing loop, foyer.
  • Monitor list: what each performer wants in their monitor.

Group the inputs logically: for a band, drums, bass, guitars, keyboards, vocals, then playback and effects; for a conference, lectern, presenters' radio mics, audience mics, then laptops and video playback. Keep the same order on every event in the same venue, so volunteers and freelancers always find things in the same place.

Start from a clean show

  1. Save the current show before changing anything, so you can go back to it. Name it clearly with the date.
  2. Load a clean starting point: the factory default or your own template. Do not build on top of an unknown show from the last user.
  3. Set the sample rate (48 kHz is the norm for live sound and video) and the clock source. In a system with stage boxes, Dante or other digital equipment, one device must be the clock master and the rest follow it.
  4. Connect the stage boxes and check the desk sees them. Most digital snakes connect with one network or fibre cable; use the type and maximum length the manufacturer specifies.
  5. Set up the network for tablet control: connect a Wi-Fi router or access point to the desk's network port, set a strong Wi-Fi password, and give the desk a fixed IP address.

Patch inputs and outputs

Inputs

  1. Open the input patch (often I/O, Patch or Routing).
  2. Assign each socket to its channel from your input list. Most desks can patch a block at once (for example, stage box inputs 1 to 32 to channels 1 to 32).
  3. Switch phantom power on for condenser microphones and active DIs. On many digital desks it is set on the preamp (socket), not the channel, so it stays with the socket whichever channel uses it.
  4. Check each channel receives the right source: line check every input by tapping microphones and playing every source.

Outputs

  1. Open the output patch.
  2. Assign each mix to its physical output: main left and right, subwoofer, monitor mixes, matrix outputs, recording and so on.
  3. Label the outputs on the desk and at the stage box, so anyone can see what each socket carries.

Networked audio

Desks with Dante or another audio network card can send and receive many channels over one network cable. Patching happens in two places: the network software (such as Dante Controller) routes channels between devices, and the desk then patches those network channels to its own channels and outputs. Document both. The Network Audio Bandwidth Calculator estimates the network load.

Name, colour and arrange

  • Name every channel and output with short, clear names ("Kick", "Lect", "Host RF", "Laptop L"). Names appear on the screen, the fader scribble strips and tablet apps.
  • Colour code by type: for example red for drums, blue for vocals, green for playback, yellow for presenters. Keep the same colours on every show.
  • Arrange the faders. Put the channels you need most often on the first layer. Many desks let you build a custom layer with any mix of channels, DCAs and masters, which is ideal for a simple operator view.
  • Assign the custom keys (soft keys, user keys) to the things you need in a hurry: tap tempo, mute groups, talkback, next scene.

For volunteers: build one layer with only what they need (DCAs for "Presenters", "Band", "Playback" and the main fader), lock everything else, and label the desk with tape. A simple, consistent layout prevents more problems than any training session.

Channel processing

Set up each channel in signal order:

  1. Gain: with the person singing, speaking or playing at performance level, set the preamp gain so the meter peaks around −18 to −12 dBFS, with loud peaks no higher than −6 dBFS.
  2. High-pass filter: on for every channel that does not need deep bass. Around 100 Hz for speech, higher for lavaliers and headsets.
  3. Gate: for drums and noisy sources only. Avoid gates on speech; use the automatic mixer instead (see below).
  4. EQ: cut problems first, boost carefully. Use the desk's real-time analyser to see what is happening.
  5. Compressor: gentle settings for speech (2:1 to 4:1, a few dB of gain reduction), more on vocals and bass in a band.
  6. Delay (on the channel): use to align a close microphone with a distant one, or a radio mic with a wired one on the same source.

Most desks can copy and paste processing between channels, and store channel presets or libraries (for "Female vocal", "Lectern", "Kick drum"). Build your own library over time.

How to Set Up Sound in a Room has a frequency guide and starting settings for EQ and compression.

Automatic mixer

For panels, conferences and meetings, assign the speech microphones to the desk's automatic mixer (automixer, Dugan). It turns down microphones nobody is speaking into, keeping the overall level steady and the number of open microphones low, which reduces feedback and room noise without anyone riding faders.

Buses, monitors and effects

Monitor mixes

  1. Set each monitor bus to pre-fade, so changes to the main mix do not affect what performers hear.
  2. Use the desk's sends on faders mode (also called mix on faders or flip): select a mix, and the faders control how much of each channel goes into that mix. It is the fastest way to build monitor mixes.
  3. Apply EQ and a limiter to each monitor output. Ring out each wedge with its output EQ before the performers arrive.
  4. Personal mixing: many desks have an app or personal mixer that lets each performer adjust their own monitor mix from a phone. Give each performer access to only their own mix.

Effects

  1. Load a reverb into an effects rack slot, and set its input to a post-fade mix bus.
  2. Patch the effect's output to an FX return channel or stereo input.
  3. Send vocals and instruments to the effect with their sends on that bus, and set the return level in the main mix.
  4. Set the effect to 100% wet; the blend is controlled by the send and return levels.

A hall or plate reverb for vocals, a shorter room reverb for drums and a tap-tempo delay cover most live needs.

Groups, DCAs and mute groups

  • Use DCAs to ride sections of the mix: all drums, all vocals, all presenters. A DCA moves the channels' levels without mixing them, so monitor sends and processing are unaffected.
  • Use groups when the combined signal needs processing, such as compressing all drums together.
  • Set up mute groups for the things you mute together: all band microphones during speeches, all presenter microphones during the band, effects between songs.

Matrix outputs

Use the matrix for feeds that need their own level, EQ or delay: delay speakers, a foyer or overflow room, the stream, a recording mix and the hearing loop. Each matrix output can take the main mix and any buses in its own proportions, so the stream can have more audience microphones and the hearing loop no effects.

Scenes and protecting settings

A scene stores the state of the desk at a moment: fader positions, mutes, processing, sends and routing. Recalling it puts everything back.

  • Save a "base" scene once the soundcheck is done, before the event starts. If anything goes wrong, you can go back to it.
  • Build scenes for each part of the event if it changes a lot: "Walk-in", "Welcome", "Panel", "Band", "Awards". Recall them in order as the event runs.
  • Use recall safe and scene filters (also called recall scope or focus) to stop some settings changing when a scene is recalled. For example, keep the main output EQ and the gain of each preamp safe, so recalling a scene does not undo the room tuning or the input levels.
  • Update scenes deliberately. On most desks, changes are not saved into a scene until you store it again.

Users and permissions

Many desks have user profiles or access levels that hide or lock parts of the desk. Set up a basic user for volunteers or guest operators, with only the faders and functions they need, and keep the patching, outputs and system settings locked behind an administrator password.

Recording and streaming

  • Stereo recording from the main mix or a matrix output to a USB stick, often built into the desk. Make sure the recording mix suits a recording: in a small room the main mix sounds unbalanced because loud instruments are heard acoustically, not through the speakers.
  • Multitrack recording over USB, Dante or a card records every channel separately to a computer, so the event can be mixed again later. It also allows a virtual soundcheck: play the recording back through the desk to set up the mix without the performers.
  • Streaming feed: send a dedicated matrix or bus to the streaming encoder, with a compressor or limiter on it, and listen to it on headphones during the event.

Save and back up

  1. Save the show file on the desk with a clear name and date.
  2. Back it up to a USB stick or laptop. Keep a copy off the desk.
  3. Keep a template for each venue or type of event, with the patching, names and output processing ready, so each event starts from a known state.
  4. Write down anything that is not in the show file: network settings, stage box IDs, Dante routing, and the order of scenes.
  5. Update the firmware carefully, between events, after backing up. Check that saved show files work with the new version, and keep every desk in a system on the same firmware.

Troubleshooting

ProblemLikely causesThings to try
No signal on a channelWrong patch, preamp not phantom powered, channel muted or in a muted mute group or DCA, stage box not connectedCheck the input patch and meter at the preamp, then follow the signal through the channel. Check mute groups and DCAs.
Signal on the channel but nothing from the speakersChannel not assigned to the main mix, output patch wrong, main fader or output mutedCheck the channel's routing to the main mix and the output patch, and watch the output meters.
A setting keeps changing backA scene recall, or the setting is controlled by a scene with a different valueStore the scene again, or set the parameter as recall safe.
Clicks, pops or dropoutsClock mismatch between devices, network problemsCheck one device is the clock master and all run at the same sample rate. Check network cables and switches.
Monitor mix changes when the main mix changesMonitor sends set to post-fadeSet monitor buses to pre-fade.
Tablet will not connectDifferent network, wrong IP range, Wi-Fi router not connected to the deskCheck the router is on the desk's network port and the tablet is on that Wi-Fi network, and check the desk's IP settings.
Feedback when a scene is recalledScene stored with microphones up or monitors loudCheck scenes before the event and keep output EQ recall safe.
Back to top