All guides
viewhub.stream · How-to Guides

How to Set Up Sound in a Room

EQ the room, choose and place microphones, stop feedback and get clear, even sound

28 min readUpdated

Contents

Before you start

Good sound in a room comes from getting a few big things right, in the right order. Most problems blamed on the mixing desk, such as feedback, boomy or muddy speech, hum or people at the back not hearing, are really caused by where the loudspeakers and microphones are, how the gain is set, or the room itself. EQ is powerful, but it is the last step, not the first.

This guide works through a typical setup from start to finish. It suits a meeting room, church, school hall, function room or small venue, for speech, live music or both:

  1. Look at the room and decide what the sound system has to do.
  2. Place the loudspeakers so they cover the audience and keep away from the microphones.
  3. Choose and position the microphones to pick up the people you want and as little of the loudspeakers as possible.
  4. Set the gain structure so every stage of the system runs at a healthy level.
  5. EQ the room, then ring out the system to push feedback further away.
  6. EQ and compress each channel so each voice and instrument sounds natural.
  7. Time-align any delay speakers, set safe levels and check the hearing loop.
  8. Soundcheck, run the event and save everything for next time.

Walk the room first

  • What is it for? Speech needs clarity and even coverage. Music also needs bass, headroom and more level. A room used for both needs a system that can do both, with saved settings for each.
  • Clap loudly and listen. A long ringing tail means a reverberant room, where speech blurs and feedback comes sooner. A sharp, fluttery echo between parallel walls is flutter echo. Both affect where speakers and microphones can go.
  • Note hard surfaces. Glass, bare plaster, hard floors and high ceilings reflect sound. Curtains, carpet, soft seating and an audience absorb it. A full room sounds noticeably drier and quieter than an empty one.
  • Listen to the background noise. Air conditioning, projectors, traffic and kitchens all set the minimum level speech has to reach.
  • Find the power, the mixing position and the cable routes. The mixing position should be in the audience area, ideally about two-thirds of the way back and on the centre line, so whoever mixes hears what the audience hears.

Kit worth having

  • Spare cables of every type you use, plus adaptors, a DI box and gaffer tape
  • Fresh or fully charged batteries for every wireless microphone and belt pack, and spares
  • A measurement microphone and RTA software, or an SPL meter app on a phone at the very least
  • A cable tester and a polarity tester if you can get them
  • Headphones for checking channels before they go out to the room
  • A torch, a notebook and a plan of the room

Understand the signal chain

Every sound system follows the same path. Knowing where each control sits in the chain makes fault-finding much quicker, because you can follow the signal from one end to the other.

Signal chain from microphone to loudspeaker MicrophoneGain (preamp)Channel EQCompressorFader and mix bus System EQDelayLimiterAmp and speaker and DI boxessets the levelper voiceevens out levelblends sources corrects the roomaligns speakersprotects speakerscovers the room
The top row happens on each channel of the mixer. The bottom row applies to each set of loudspeakers, in the mixer outputs, a loudspeaker processor or the amplifier.

The key idea is that channel processing fixes the source (this voice is boomy, this guitar is too bright) and system processing fixes the room and the loudspeakers (this room booms at 125 Hz, these delay speakers are 15 metres back). Keep the two separate. If you EQ the system to fix one presenter's voice, every other microphone suffers.

Power on and off in the right order

Switch on sources and the mixer first, then processors, then amplifiers or powered loudspeakers last. Switch off in the reverse order: amplifiers and loudspeakers first. This stops the loud thumps that can damage drivers and startle the audience. Mute or turn down a channel before plugging or unplugging anything, and before switching phantom power on or off.

Place the loudspeakers

Loudspeaker placement decides how even the coverage is and how much sound reaches the microphones. It is the single biggest factor in how loud you can go before feedback.

Plan view of a room showing loudspeakers in front of the microphones Stage Audience Main speakers, in front of the microphones Delay speakers Microphones
Keep every loudspeaker in front of (downstage of) every microphone, aimed at the audience and away from the stage. Delay speakers cover the rear of long rooms.

The main rules

  • Loudspeakers in front of microphones. Put the main speakers forward of the line where people stand to speak or perform, so the microphones are behind them. A speaker behind or beside a microphone pointing at it is the classic recipe for feedback.
  • Aim at the audience, not the walls. Sound hitting the side walls, back wall and ceiling bounces back as reverberation, muddying speech and feeding back into microphones. Angle speakers in towards the seating and down towards the back third of the audience.
  • Get them high enough. The high-frequency drivers should be above the heads of a standing audience (usually 2 to 2.5 metres to the bottom of the cabinet) so the front rows do not block the sound for everyone behind. Tilt them down so the coverage lands on the audience.
  • Do not blast the front row. Level drops by about 6 dB each time the distance doubles. If the front row is 2 metres away and the back row is 16 metres, that is an 18 dB difference from a single speaker. Raising and angling the speaker, or adding delay speakers or front fills, evens this out.
  • Use the right number. A stereo pair suits most small rooms. Long rooms need delay speakers about halfway back. Low-ceilinged or very wide rooms, and rooms with columns, often work better with a distributed system of many ceiling or wall speakers at lower level.
  • Subwoofers on the floor. Bass is reinforced by the floor, and more again in corners, which can make it boomy. Keep subwoofers at the front, check bass at several seats, and keep them away from stage microphones.

Tip: For music, mono often works better than stereo in a wide room. Someone sitting at the far left of a stereo system hears mostly the left speaker, so anything panned hard right almost disappears for them. For speech, always run the system in mono.

Check polarity

Every loudspeaker in a system should push outwards together on the same signal. If one is wired the wrong way round (out of polarity), the bass cancels where their sound overlaps and the system sounds thin. Play music with plenty of bass through a pair, then flip the polarity of one in the processor or amplifier: the setting with more bass is correct. A polarity tester makes this quick.

The Speaker Coverage & SPL Calculator and Ceiling Speaker Layout Planner help with coverage and spacing.

Choose the right microphones

The best microphone is the one that picks up the wanted sound as loudly as possible and the loudspeakers as little as possible. That comes down to the type of microphone and its polar pattern, meaning which directions it hears best.

Microphone types

TypeBest forThings to know
Dynamic handheldVocals, presenters, guitar amps, drumsTough, needs no power and handles very loud sound. Must be used close to the mouth.
Condenser handheldVocals in controlled settingsMore detail and sensitivity than a dynamic, but more prone to feedback and handling noise. Needs phantom power or a battery.
Small-diaphragm condenserChoirs, acoustic instruments, overheadsAccurate pick-up at a distance. Needs phantom power.
GooseneckLecterns, pulpits, conference tablesUsually a cardioid or supercardioid condenser on a flexible stem.
HeadsetPresenters who move around, theatre, fitnessStays a fixed short distance from the mouth, so it gives the most gain before feedback of any hands-free microphone.
Lavalier (lapel or tie clip)Presenters, interviews, videoDiscreet, but sits 15 to 25 cm from the mouth. Often omnidirectional, so feedback comes sooner than with a headset.
Boundary (plate)Meeting tables, stage floors for dramaSits flat on a surface. Picks up a wide area but also table knocks and paper noise.

Polar patterns

Directional microphones are least sensitive in particular directions, called nulls. The trick is to aim the microphone at the person and put the loudspeakers, especially foldback wedges, in its nulls.

Cardioid and supercardioid polar patterns with the best places for monitor speakers Cardioid: null at 180°Supercardioid: nulls at about 125° TalkerTalker
A cardioid rejects sound from directly behind, so one wedge goes straight behind the microphone. A supercardioid has a slight rear lobe, so its quietest points are at about 125° either side: two wedges angled in at the sides work best.
PatternPicks upQuietest directionUse it for
OmnidirectionalAll round equallyNoneLavaliers, measurement, recording a room. Not for loud live sound.
CardioidFront, with the sides about 6 dB downDirectly behind (180°)Most vocal and presenter microphones; a good all-rounder.
SupercardioidA narrower frontAbout 125° either sideLoud stages and lecterns. Needs careful aiming.
HypercardioidNarrower stillAbout 110° either sideVery loud stages and shotgun-style pick-up. Rejects less directly behind.
Figure of eightFront and back equallyThe sides (90°)Two-person interviews, some studio techniques.

All directional microphones boost the bass as the source gets closer, called the proximity effect. It makes a close-up voice warm, but boomy if overdone. The high-pass filter and channel EQ deal with it.

Position microphones to stop feedback

The closer a microphone is to the person, the louder their voice is compared with everything else the microphone hears. Each time the distance halves, the wanted sound goes up by about 6 dB. That 6 dB comes straight off the amount you need to turn up, so it is 6 dB further from feedback. No EQ or feedback suppressor comes close.

Distances that work

MicrophoneDistance from the mouthHow to position it
Handheld vocal2 to 10 cmPoint it at the mouth and hold the handle, not the grille. Cupping the grille turns a cardioid into an omni and causes feedback.
Headset1 to 3 cmAt the corner of the mouth, just out of the breath path so plosives (p and b) and breathing are not picked up.
Lavalier15 to 20 cmCentre of the chest, a hand's width below the chin, clear of jewellery, ties and collars. If the presenter turns to one side a lot (for example to a screen), clip it on that side.
Lectern gooseneck15 to 30 cmJust below chin height, aimed at the mouth from slightly below. Make sure it points away from any loudspeaker and above the reading surface, to avoid paper noise and reflections.
Boundary on a tableUp to about 1 m per talkerFlat on the table, front edge facing the talkers, away from laptops, projector fans and coffee cups.
ChoirAbout 0.6 to 1 m in front of and above the front rowAim at the back row so all rows are picked up evenly. Use one microphone per section rather than many, spaced using the 3:1 rule.
Instrument amp2 to 5 cm from the grillePoint at the centre of the speaker cone for bite or towards the edge for a warmer sound.

The 3:1 rule

When two microphones pick up the same source, the slight difference in arrival time causes cancellations that make the sound thin and phasey, called comb filtering. Keep the distance between microphones at least three times the distance from each microphone to its source. For example, if the lectern microphone is 25 cm from the speaker's mouth, any other open microphone should be at least 75 cm away. Never place two microphones on the same lectern unless one is a spare that stays muted.

Quick rules for fewer problems

  • Point microphones away from loudspeakers, and put loudspeakers in the microphones' nulls.
  • Do not walk in front of the main speakers with a live microphone. Mark the floor if presenters move around.
  • Keep the number of open microphones as low as possible. Each time the number of open microphones doubles, the system is about 3 dB closer to feedback. Mute anything not in use, or use an automatic mixer for panels and meetings.
  • Choose a headset rather than a lavalier for anyone who is quiet, moves near the loudspeakers or speaks in a large or reverberant room.
  • Coach the presenter. Ask quiet speakers to come closer to the microphone, rather than turning them up past the point of feedback.
  • Keep microphones away from hard surfaces directly in front of the mouth, such as a laptop lid, glass lectern or wall. These reflect the voice back with a slight delay and cause comb filtering.
  • Use windshields outdoors and pop shields or foam for close vocal work.

Set up wireless microphones

Frequencies and licences in the UK

Radio microphones must use frequencies that are legal in the UK. Some bands are licence-exempt, including 863 to 865 MHz, a small part of the VHF band at 173.7 to 175.1 MHz, and the 2.4 GHz band used by many digital systems. These are free to use but crowded, and only allow a few UHF systems at once. Most professional UHF systems use Channel 38 (606 to 614 MHz), which needs an inexpensive shared licence from Ofcom. Larger events can book co-ordinated frequencies from Ofcom too. Check the frequency range printed on the receiver before buying second-hand or imported equipment, as older systems in Channel 69 (854 to 862 MHz) and many imported systems are no longer legal to use.

Setting up

  1. Switch on all the receivers with their transmitters switched off, and run each receiver's frequency scan, or the group scan on a multi-receiver system. Use the manufacturer's preset groups: their frequencies are chosen so the systems do not interfere with each other.
  2. Sync each transmitter to its receiver and label both with the name and frequency.
  3. Fit fresh batteries, or fully charged rechargeables, before every event. Do not trust a half-used battery for a long event.
  4. Set the transmitter gain or sensitivity so that loud speech or singing just avoids the peak light on the receiver. Then set the mixer gain as for any other microphone.
  5. Keep receiver antennas in line of sight of the stage, clear of metal racks and away from LED screens, lighting dimmers and Wi-Fi access points. Use remote antennas at the front of the room if the receivers are in a rack at the back.
  6. Walk the whole presenting area with each microphone, listening on headphones for dropouts, before the audience arrives.

Watch out: a lavalier or headset left switched on in a pocket, on a table or in the toilets is picked up by the whole room. Keep its fader down until the presenter is on stage, and tell presenters where the mute switch is.

Why feedback happens

Feedback is the howl or ring you hear when sound from a loudspeaker goes back into a microphone, is amplified again, comes out of the loudspeaker louder, and goes round the loop again. It starts at whichever frequency gets round the loop with the most gain, which depends on the loudspeaker, the microphone and the room. Long before it howls, a system near feedback sounds ringy and hollow, with a lingering tone after each word.

The feedback loop MicrophoneMixer and ampLoudspeaker Sound from the loudspeaker returns to the microphone through the air and off the walls+ gain+ gain
When the gain round the loop at any frequency reaches unity, feedback builds on its own.

Fixes, most effective first

  1. Move the microphone closer to the person. Halving the distance gains about 6 dB.
  2. Move the loudspeakers so they are in front of the microphones and pointing away from them. Moving a loudspeaker from beside a microphone to well in front of it can gain 10 dB or more.
  3. Use directional microphones and aim their nulls at the loudspeakers and wedges.
  4. Reduce the number of open microphones. Halving them gains about 3 dB.
  5. Reduce reflections near the microphones and loudspeakers: angle speakers away from walls, add soft furnishing, and close curtains over glass.
  6. Ring out the system with EQ. This typically gains another 3 to 6 dB once everything above is done.
  7. Use an automatic feedback suppressor only as a safety net. It works by cutting notches as feedback starts, so the audience still hears the start of each howl, and too many notches make the sound thin.

Rule of thumb: keep the normal operating level at least 6 dB below the point where the system first starts to ring. That margin absorbs a presenter stepping forward, a door opening or the room filling up.

Set the gain structure

Gain structure means setting the level at each stage of the system so the signal is well clear of the background hiss but never distorts. Most hiss, distortion and feedback problems at the mixer come from the input gain being set badly and then made up with faders.

  1. Start with everything down: channel faders, master faders and amplifier controls. Set channel EQ flat and switch off any effects.
  2. Set amplifier or powered speaker inputs to the manufacturer's recommended setting, often fully up or 0 dB, so the mixer output drives them correctly. If the system is too loud with the master fader at unity, turn the amplifiers down rather than running the mixer very low.
  3. Ask the person to speak or sing at performance level, not a quiet "one, two". Most people get much louder once the event starts.
  4. Adjust the channel gain (also called trim or preamp) using the pre-fade listen (PFL) or channel meter. On a digital mixer, aim for normal speech around −18 dBFS with peaks between −12 and −6 dBFS. On an analogue mixer, aim for peaks around 0 VU and never let the peak light come on.
  5. Bring the fader up to around unity (0 dB) and use the master fader to reach the level you need in the room.
  6. Check the outputs. The master meters should run well below clipping, with the amplifier limit or clip lights only flickering occasionally, if at all.

Phantom power: condenser microphones and active DI boxes need 48 V phantom power, switched on at the mixer. Mute the channel before switching it on or off. Do not use phantom power with unbalanced cables or adaptors, and check before using it with ribbon microphones, as some vintage ribbons can be damaged by it.

The Microphone Gain Structure Calculator works out the gain a microphone needs, the headroom to clipping and the signal-to-noise ratio, and the dB Toolbox converts dBu to volts.

EQ the room

Every room changes the sound of a loudspeaker. Bare parallel walls reinforce some bass notes (room modes) and cancel others, and hard surfaces exaggerate the treble. System EQ corrects the overall tonal balance, so the system sounds natural before any microphones are opened.

What you need

  • A measurement microphone (an omnidirectional microphone with a flat response, ideally with a calibration file) on a stand at ear height
  • Pink noise from the mixer's built-in generator or a test file. Pink noise has equal energy in every octave, so a flat system shows a flat line on an analyser
  • A real-time analyser (RTA). Many digital mixers have one built in; free programs such as Room EQ Wizard work on a laptop
  • A parametric or 31-band graphic EQ on the output feeding each set of loudspeakers

How to do it

  1. Start flat. Reset the system EQ, and set the high-pass filters on the main speakers to the manufacturer's recommended settings.
  2. Play pink noise at a moderate level, around 80 to 85 dB(A) at the measurement position, well above the room's background noise.
  3. Measure at several seats: front, middle, back and to the sides, but not right next to a wall or directly on the centre line between two speakers. Average the readings, or use the analyser's averaging, so you correct the room rather than one seat.
  4. Look for broad trends, not narrow spikes. Use 1/3 or 1/6 octave smoothing.
  5. Cut the peaks with wide, gentle filters: typically 2 to 6 dB, with a Q of about 1 to 2 (roughly one octave wide). Common culprits are a bass hump between 80 and 250 Hz and harshness between 2 and 5 kHz in hard rooms.
  6. Do not boost the dips. Narrow dips are usually cancellations that change from seat to seat. Boosting them wastes amplifier power and loudspeaker excursion, increases feedback, and only fixes one position.
  7. Aim for a natural target: roughly flat through the midrange, gently falling by a few dB towards 10 to 16 kHz, with a little more bass for music if wanted. A system that measures dead flat at high frequencies usually sounds harsh.
  8. Listen. Play well-known recorded speech and music you know well, walk the room and adjust by ear. The measurement gets you close; your ears finish the job.

What EQ cannot fix

EQ cannot remove echo or reverberation, fix a speaker pointing the wrong way, or fill in a deep bass null in one part of the room. If speech is hard to understand in a very reverberant room, the answer is closer microphones, loudspeakers aimed at the audience and away from walls, more loudspeakers at lower level closer to the listeners, and acoustic treatment. As a guide, meeting rooms and classrooms work best with a reverberation time of around 0.6 to 0.8 seconds, and more than about 1.5 seconds makes speech hard work.

The Reverberation Time Calculator estimates how reverberant a room is and how much absorption would help.

Ring out the system

Ringing out finds the frequencies that feed back first with the microphones in their real positions, and cuts them with narrow filters, so the system can run louder before feedback. Do it after the room EQ and before the soundcheck, with the stage set up as it will be on the day.

  1. Place the microphones where they will be used, with wedges and loudspeakers in their final positions and the channel EQ flat. Ring out each microphone on its own, then all of them together.
  2. Set the channel gain for a normal voice, then slowly raise the fader or master until the system just starts to ring. Do it carefully and in small steps: protect your hearing and your loudspeakers.
  3. Find the frequency using the mixer's RTA, a feedback finder, or by sweeping a narrow boosted parametric band until the ring jumps out. With practice you learn to recognise the pitch by ear.
  4. Cut that frequency by 3 to 6 dB using a narrow filter (Q around 5 to 10, or about 1/6 to 1/10 octave). On a graphic EQ, pull the nearest slider down by the same amount.
  5. Raise the level again until the next frequency starts to ring, and repeat.
  6. Stop after about five or six filters, or when the gain gained becomes small. Beyond that, the cuts start to change the tone of the voice for little benefit.
  7. Set your maximum level about 6 dB below the point where ringing started on the last pass, and note it.
  8. Repeat for foldback wedges, which usually ring before the main system. Ring out each monitor mix separately using the EQ on that output.

Tip: if the same frequency keeps ringing on several microphones, cut it in the system or wedge EQ. If it only rings on one microphone, cut it on that channel instead.

EQ each microphone and instrument

With the system sounding natural and rung out, channel EQ shapes each source. Start by cutting what is not wanted, then add small boosts only where they make a clear improvement.

Always use the high-pass filter

Switch on the high-pass (low-cut) filter on every channel that does not need deep bass. It removes handling noise, footsteps, air-conditioning rumble and proximity-effect boom, and frees the amplifiers and loudspeakers to work on sound the audience can actually use.

  • Speech microphones: 80 to 120 Hz, often around 100 Hz
  • Lavaliers, headsets and lectern microphones: 120 to 150 Hz
  • Female and children's vocals, acoustic guitar, overheads: 100 to 200 Hz
  • Bass guitar, kick drum and keyboards with low notes: leave off, or set below 40 Hz

Frequency guide

RangeToo much soundsWhat to do
Below 80 HzRumbly, unclearHigh-pass filter on everything except bass instruments.
100 to 250 HzBoomy, chestyCut a few dB on close vocal microphones affected by proximity effect.
250 to 500 HzMuddy, boxyA common cut for lavaliers, table and lectern microphones, and in small rooms.
500 Hz to 1 kHzHonky, nasalSmall, gentle cuts if a voice sounds like it is through a cardboard tube.
2 to 5 kHzHarsh, shoutyThe presence and intelligibility region, where hearing is most sensitive. A small boost aids clarity; too much tires listeners and causes feedback.
5 to 8 kHzSibilant ("s" sounds)Cut gently or use a de-esser on bright voices and condenser microphones.
8 to 16 kHzHissy, brittleA gentle shelf boost adds air to vocals and cymbals; cut if the noise floor is noticeable.

A speech microphone that sounds dull is usually better fixed by cutting the low mids than by boosting the treble, because a treble boost also boosts feedback. Make EQ decisions at performance level, in the room, and compare with the EQ bypassed now and then to check you have actually improved it.

Compression, gates and limiters

Compressor

A compressor turns down loud passages automatically, so a speaker who varies between murmuring and shouting stays at a more even level. Typical settings for speech are:

  • Ratio 2:1 to 4:1
  • Attack 5 to 20 ms
  • Release 100 to 200 ms, or automatic
  • Threshold set so normal speech gives 3 to 6 dB of gain reduction

Use a little more on vocals in a band, and less on choirs and acoustic music. Compression raises the quiet parts relative to the loud parts, which also brings up background sound and the system itself. Add it after ringing out, and check again for ringing afterwards.

Gates and automatic mixers

A noise gate mutes a channel when its level falls below a threshold. It suits drums but can chop words off a presenter. For panels, conferences and meetings with several speech microphones, an automatic mixer (built into many digital mixers and conference processors) is far better. It keeps the overall gain steady by turning down microphones that are not being spoken into, which keeps the number of open microphones low.

Limiter

Put a limiter on the outputs feeding the loudspeakers, set just below the level at which the amplifiers clip or the loudspeakers' rated limit. It protects the system from dropped microphones, unplugged cables and over-enthusiastic presenters. It should only act occasionally; if it is working all the time, the system is too small or too loud.

Time-align delay speakers

Sound travels at about 343 metres per second, or roughly 2.9 ms per metre at room temperature. Electrical signals arrive almost instantly, so a delay speaker halfway down a room plays before the sound from the main speakers reaches it. Listeners hear a smeared echo, and the voice seems to come from the nearest speaker instead of the stage.

  1. Measure the distance from the main speakers to the delay speakers along the path the sound travels.
  2. Multiply by 2.9 to get the delay in milliseconds. For example, 15 m × 2.9 = 43.5 ms.
  3. Add about 5 to 15 ms more. Because the main speakers' sound now arrives first, the brain places the voice on the stage, even though the delay speaker is louder. This is called the precedence or Haas effect.
  4. Set the delay speakers' level so they fill in the rear without being obviously louder than the mains for people sitting in front of them.
  5. Check by ear standing just behind the delay speakers: speech should sound clear, as one source, and seem to come from the front.

The same approach aligns a subwoofer with the main speakers, front fills with the main system, and even the main speakers with a loud drum kit or guitar amplifier on a small stage. The Speaker Delay Time Calculator works it out, including the effect of temperature.

Set sensible levels

Louder is not clearer. Speech is most intelligible when it is comfortably above the background noise, typically about 15 dB, and no louder. Measure at several seats using an SPL meter set to A-weighting.

UseTypical average level at the audience
Speech in a quiet meeting room or church65 to 75 dB(A)
Speech at a busy function or exhibition75 to 85 dB(A)
Background music under conversation60 to 70 dB(A)
Acoustic or worship music80 to 90 dB(A)
Live band or DJ90 to 100 dB(A)

Protect hearing: in the UK, the Control of Noise at Work Regulations 2005 apply to staff, crew and performers. Employers must assess the risk and provide information and training at a daily exposure of 80 dB(A), and provide hearing protection and control the noise at 85 dB(A). Exposure must not exceed 87 dB(A), allowing for hearing protection. For audiences, the World Health Organization recommends that the average level in a venue stays at or below 100 dB(A) over any 15 minutes, with quiet areas available.

The Speaker Coverage & SPL Calculator estimates the level a loudspeaker produces at a distance, and the dB Toolbox adds, subtracts and converts decibel levels.

Hearing loops and accessibility

A hearing loop (audio induction loop) sends the sound system's audio as a magnetic field around a cable laid around the room. Hearing aids and cochlear implants set to the T (telecoil) setting pick it up directly, without the room's echo and background noise. Under the Equality Act 2010, service providers must make reasonable adjustments for disabled people, and a working loop is often one of them in public venues, places of worship and meeting rooms.

  • Feed the loop from a clean, mixed output, such as a post-fader auxiliary or matrix output, carrying speech and programme sound but not the hiss of unused microphones.
  • Include every microphone that matters, plus video playback and video calls.
  • Do not add delays or heavy reverb to the loop feed. Hearing aid users want the dry, direct sound.
  • Test it before every event with a loop listener. The standard BS EN IEC 60118-4 sets the field strength (a reference of 400 mA/m) and a flat response from 100 Hz to 5 kHz, which a loop installer can verify.
  • Display the loop sign (the ear symbol with a T) where it is visible, and only where the loop actually works.

Other ways to help include clear, well-lit faces for lip reading, live captions on screen, and keeping background music off during speech.

Cabling, power and interference

Cables

  • Use balanced connections (XLR, or TRS jack) for microphones and for long runs between equipment. Balanced cables reject hum and interference picked up along the way. Unbalanced cables (guitar leads, RCA phono) should be kept short, ideally under 5 m.
  • Use a DI box to connect instruments, laptops and phones to the mixer. It converts their unbalanced output to a balanced microphone-level signal, suitable for a long cable, and its ground lift switch can cure hum.
  • Keep audio cables away from mains, lighting dimmers and LED screen power. Where they must meet, cross at right angles.
  • Coil cables over-under so they lay flat without twisting, and label both ends.
  • Tape down or cover cables across walkways with cable ramps or mats. Trip hazards are the most common cause of injury at events.
  • Use speaker cable for loudspeakers, never microphone or instrument cable, and size it for the length and impedance. The Speaker Cable Size Calculator works this out.

Hum and buzz

A steady 50 Hz hum, or a buzz with 100 Hz and higher harmonics, is usually a ground loop, caused by equipment connected together through audio cables and also earthed through different mains sockets. To find it, unplug inputs one at a time until it stops. Cures, in order:

  1. Power all the audio equipment from the same mains distribution point.
  2. Use balanced cables throughout.
  3. Use the ground lift switch on a DI box, or an audio isolation transformer, on the offending connection.

Never remove or disconnect the mains earth from any plug, lead or piece of equipment to cure hum. The earth is a safety connection that stops metalwork becoming live in a fault. Equipment used for events should be electrically tested regularly, and temporary power should be set up by a competent person.

Soundcheck and on the day

Before the doors open

  • Every loudspeaker working, in polarity and at the right level
  • Pink noise and familiar music checked at several seats
  • Each microphone checked through headphones, then through the room, by the person who will use it, at performance level
  • Wireless microphones walked round the whole presenting area, with fresh batteries and spares to hand
  • Monitor mixes agreed with the performers
  • Laptop, video and video-call audio checked at their real levels, with notifications and system sounds switched off
  • Hearing loop tested with a loop listener
  • Maximum level noted and the scene saved on the mixer
  • Cables taped down and walkways clear
  • Playback for walk-in music, and a plan for what plays if a presenter's video fails

During the event

  • Stay at the mixer and keep your hand near the faders of open microphones.
  • Bring each microphone up just before the person starts speaking, and back down when they finish.
  • Expect to need slightly more level once the room fills, as people absorb sound and add noise. Re-check from the back of the room.
  • If feedback starts, pull the offending channel or the master down quickly, then work out the cause. Do not leave the master up and hunt for the frequency while the audience suffers.
  • Watch the presenters. If someone drifts away from the microphone, a discreet signal to come closer is better than chasing them with the fader.

Troubleshooting

ProblemLikely causesThings to try
No sound from a microphoneChannel muted, gain down, wrong input, phantom power off, faulty cable, wireless transmitter muted or flatCheck the channel meter, then work along the chain. Swap the cable, try the microphone in another channel, check batteries and the mute switch.
Feedback or ringingMicrophone too far from the talker, loudspeakers behind or beside microphones, too many open microphones, too much gain or EQ boostPull the level down. Move the microphone closer and the loudspeaker forward, mute unused microphones, then ring out the system again.
Hum or buzzGround loop, unbalanced cable, audio cable near mains or dimmersUnplug inputs one at a time to find it, use a DI box with ground lift, and reroute cables. Never remove the mains earth.
HissGain too low with faders too high, or a noisy sourceReset gain structure: more input gain, less fader.
DistortionInput gain too high, clipping in the mixer or amplifier, damaged loudspeakerWatch the peak lights along the chain and reduce the stage that is clipping.
Muddy or boomy speechNo high-pass filter, proximity effect, room bass build-up, too much reverberationHigh-pass at 100 to 150 Hz, cut 200 to 400 Hz, aim loudspeakers away from walls, check room EQ.
Harsh or tiring soundToo much 2 to 5 kHz, system too loud, loudspeakers aimed straight at the listeners' ears at close rangeCut gently around 2.5 to 4 kHz, reduce overall level, re-aim loudspeakers.
Thin or phasey soundTwo microphones on one source, a loudspeaker out of polarity, a reflective surface near the microphoneApply the 3:1 rule, check polarity, move the microphone away from hard surfaces.
Fine at the front, poor at the backLoudspeakers too low, aimed too low, or too far away for a long roomRaise and re-aim the loudspeakers, or add time-aligned delay speakers.
Wireless dropouts or noiseFlat battery, antennas blocked, interference, frequency clashFit a fresh battery, move antennas into line of sight, rescan and choose frequencies from one preset group.

Afterwards

  • Save the mixer scene with a clear name and date, and back it up to a USB stick or laptop.
  • Write down the system EQ, ringing-out frequencies, delay times, maximum safe level and microphone positions. A photo of the stage layout helps.
  • Note anything that went wrong and what fixed it, plus kit that needs repairing or replacing.
  • Remove batteries from wireless microphones that will be stored, and charge rechargeables.
  • Next time, start from the saved scene but always check by ear. The room, the audience, the presenters and the weather all change how a system behaves.
Back to top