All guides
viewhub.stream · How-to Guides

HDMI and Video Signal Troubleshooting

Fix no signal, dropouts, wrong resolutions and black screens: cables, bandwidth, EDID, HDCP and extenders

8 min readUpdated

Contents

Before you start

"No signal" is the most common problem in AV. A laptop that will not show on the screen, a picture that flickers or drops out, a black screen from a streaming box, or a display stuck at the wrong resolution usually come down to a handful of causes: the cable or its length, the resolution and bandwidth, EDID, HDCP, or something in between such as a switcher or extender. This guide explains how video signals connect and negotiate, then gives a step-by-step method for finding and fixing faults.

The quickest fix: simplify. Connect the source straight to the display with a short, known-good cable. If that works, add the other equipment back one piece at a time until the fault returns.

How an HDMI connection works

When you plug in an HDMI cable, the source and display have a short conversation before any picture appears:

The steps of an HDMI connection between a source and a display SourceDisplay1. Hot plug: "I am here"2. EDID: "I can show these formats"3. Video in the chosen format4. HDCP authentication
Any device in between, such as a switcher, splitter or extender, takes part in each of these steps. If one step fails, there is no picture.
  1. Hot plug detect: the display tells the source it is connected and ready.
  2. EDID: the source reads the display's EDID (extended display identification data), a list of the resolutions, frame rates, colour formats and audio formats it supports.
  3. The source chooses a resolution and format from that list, usually the display's preferred (native) one, and starts sending video.
  4. HDCP: if the content is copy-protected, the source and display authenticate each other with HDCP. If this fails, the source sends a black screen, an error message or a lower-quality picture.

Versions, resolution and bandwidth

Higher resolutions, frame rates and colour depths need more bandwidth. Every part of the chain (source, cable, switcher, extender and display) must support the bandwidth of the signal, or the picture fails or drops out.

VersionMaximum bandwidthTypical capabilityCable to look for
HDMI 1.410.2 Gbps1080p at 60 Hz, 4K at 30 HzHigh Speed
HDMI 2.018 Gbps4K at 60 Hz (8-bit 4:4:4, or HDR with 4:2:2 or 4:2:0)Premium High Speed
HDMI 2.148 Gbps4K at 120 Hz, 8K, full HDR at high frame ratesUltra High Speed
  • Chroma subsampling (4:4:4, 4:2:2, 4:2:0) reduces colour detail to save bandwidth. It is fine for video but makes small coloured text look fuzzy on computer content.
  • HDR and higher bit depths (10 or 12-bit) need more bandwidth than standard 8-bit.
  • Refresh rate: computers sometimes default to unusual rates (59.94, 75 or 144 Hz) that some displays and processors do not accept.

The Video Bandwidth & Storage Calculator works out the bandwidth of any video format.

Cables and distance

MethodTypical reachNotes
Passive HDMI cableAbout 3 to 5 m at 4K 60 Hz, up to 10 to 15 m at 1080pUse certified cables. Longer passive cables often fail at high resolutions.
Active HDMI cableUp to about 15 to 30 mContains electronics; usually works in one direction only, so plug the "source" end into the source.
Optical HDMI cable (AOC)Up to 100 m or moreThin and light, carries full bandwidth. Directional, and must not be bent tightly.
HDBaseT extenderUp to 100 m over Cat6 cableCarries video, audio, control and often power over one network-type cable (point to point, not through a network switch). Most support 4K at 30 Hz uncompressed, or 4K at 60 Hz with 4:2:0 or light compression.
Fibre extenderHundreds of metres to many kilometresFor long runs and electrically noisy environments. See the Fibre Link Budget Calculator.
AV over IPAcross a networkEncoders and decoders on a network switch, for flexible routing to many displays. Uses compression on 1 Gb networks, or very light or no compression on 10 Gb networks.
SDI (3G or 12G)Typically 70 to 100 m on good coaxial cable, less at 12GLocking BNC connectors, the standard for broadcast and live production cameras.
  • Use certified cables (look for the official HDMI certification label for Premium High Speed or Ultra High Speed).
  • Avoid adapters and couplers in long runs: every join weakens the signal.
  • Support the connectors. HDMI plugs do not lock and are easily pulled out or damaged. Use cable supports, locking HDMI cables where possible, and leave strain relief.
  • USB-C and DisplayPort: laptops often output video over USB-C (DisplayPort Alternate Mode). Check the port supports video, and use a good-quality adapter.

The Network Cable Reach Calculator helps with HDBaseT and network cable runs.

EDID problems

EDID tells the source what to send. When there are several displays, a switcher or an LED processor in between, the source may see the wrong EDID, or none at all.

  • Wrong resolution: the source reads the EDID of a switcher or processor that asks for something different from the display. Set the EDID on the switcher or processor to match the display, or choose a fixed EDID.
  • Different displays on a splitter: the source picks a format one display cannot show. Set the splitter to use the EDID of the least capable display, or a fixed common format such as 1080p.
  • Blank screen after switching: when a switcher changes input, sources may see the display "disconnect" and change resolution. An EDID emulator (EDID manager) holds a fixed EDID so the source always sees a display.
  • Custom resolutions: LED processors use EDID to ask sources for the screen's exact resolution. Some sources (especially Macs and some media players) need help to accept non-standard sizes. See the input settings in the VX Pro guide.

HDCP problems

HDCP (high-bandwidth digital content protection) stops protected content (streaming services, Blu-ray, many set-top boxes and some Apple devices) being copied. Every device in the chain must support HDCP, and the right version.

  • HDCP 2.2 or later is needed for most 4K protected content. An older switcher, splitter, extender or capture device that only supports HDCP 1.4 makes the source fall back to a lower resolution or show nothing.
  • Too many devices: HDCP limits how many displays one source can feed through splitters.
  • Capture and streaming: capture cards and recorders refuse HDCP content by design. Use unprotected sources for anything recorded or streamed.
  • Turn it off where you can: for presentations from laptops, many sources and processors let you switch HDCP off, which avoids problems with equipment that does not support it.

A step-by-step fault-finding method

  1. Check the obvious: power on, correct input selected on the display, cables fully plugged in, the source not asleep, and the laptop actually set to output (duplicate or extend the display: Windows key + P on Windows, or display settings on a Mac).
  2. Look at what the display says: "no signal" means nothing is arriving; "unsupported format" or "out of range" means the resolution or frame rate is wrong; a black screen with signal, or an error message, often means HDCP.
  3. Go direct: connect the source to the display with a short, known-good cable, bypassing every switcher, extender and adapter.
  4. If direct works, add each piece of equipment back one at a time until the problem returns. The last thing added is the cause.
  5. If direct fails, try a different source, then a different display, to find which end is at fault.
  6. Lower the format: set the source to 1080p at 60 Hz, 8-bit. If that works, the problem is bandwidth (cable, extender or version), EDID or a format the display does not accept.
  7. Power cycle in order: switch off everything, then switch on the display first, then any devices in between, then the source last. This lets each device read the EDID correctly.
  8. Check HDCP: try unprotected content (a laptop desktop) on the same chain. If that works but the streaming box does not, HDCP support is the problem.
  9. Record the fix, including the working resolution, EDID setting and equipment order, so it is quick next time.

Symptoms and fixes

SymptomLikely causesThings to try
No signalWrong input, source asleep or not outputting, faulty cable, power-on orderCheck the input and laptop display mode, swap the cable, power cycle with the display first.
Picture drops out or sparklesCable too long or poor quality, bandwidth beyond the cable or extenderUse a shorter or certified cable, an active or optical cable, or reduce the resolution or frame rate.
"Unsupported format" or "out of range"Source sending a resolution or refresh rate the display cannot showSet the source to the display's native resolution at 60 Hz, or fix the EDID.
Black screen from a streaming box or Blu-rayHDCP not supported somewhere in the chainConnect direct to test, and use HDCP 2.2 equipment throughout.
Picture works but no audioAudio format not supported, audio routed elsewhere, display mutedSet the source to stereo PCM audio, and check the audio output settings and EDID audio.
Wrong resolution or picture too smallSource reading the wrong EDID, overscan or underscan on the displaySet the EDID, and set the display to "just scan", "1:1" or "screen fit".
Colours wrong, washed-out blacksLimited and full range RGB mismatch, YCbCr and RGB mismatchSet the source and display to the same colour range, usually full range RGB for computers.
Fuzzy coloured textChroma subsampling (4:2:0 or 4:2:2)Use 4:4:4 at a frame rate the chain can carry, or a lower resolution.
Works for a while then drops outOverheating extender or switcher, loose connector, power supplyCheck ventilation, secure the connectors, and check power supplies.

A troubleshooting toolkit

  • Short and long certified HDMI cables, including an optical cable
  • Adapters: USB-C to HDMI, DisplayPort to HDMI, Mini DisplayPort to HDMI
  • An EDID emulator, to fix the EDID a source sees
  • A signal generator or a laptop you can set to any resolution
  • A small test monitor that accepts most formats
  • An HDMI signal analyser, which shows the resolution, frame rate, colour format and HDCP status of a signal
  • Locking cable supports and spare power supplies for extenders
Back to top