All guides
viewhub.stream · How-to Guides

How to Configure a NovaStar VX Pro Processor

Choose the model, map the LED screen, set the inputs, build layers and scale the picture on a VX400 Pro, VX600 Pro, VX1000 Pro or VX2000 Pro

21 min readUpdated

Contents

Before you start

The NovaStar VX Pro series are all-in-one LED controllers. Each one combines a video processor (inputs, scaling, layers and presets) and a sending card (the Ethernet outputs that drive the screen) in one box. This guide takes you from unboxing to a working show: choosing the model, cabling and mapping the screen, setting the inputs, building layers, scaling the picture, and saving everything so it comes back the same every time.

It covers the VX400 Pro, VX600 Pro, VX1000 Pro and VX2000 Pro. Menu and page names are shown in this style. They can change slightly between firmware versions, so keep the firmware up to date and check the user manual if something does not match.

The models

ModelEthernet portsLoading capacityLayer resourcesMain video inputs
VX400 Pro42.6 million pixels6HDMI 2.0, 2 × HDMI 1.3, 3G-SDI, fibre, USB
VX600 Pro63.9 million pixels6HDMI 2.0, 2 × HDMI 1.3, 3G-SDI, fibre, USB
VX1000 Pro106.5 million pixels6HDMI 2.0, HDMI 1.3, 3G-SDI, fibre, USB
VX2000 Pro2013 million pixels12DP 1.2, 2 × HDMI 2.0, 4 × HDMI 1.3, 12G-SDI, fibre, USB

The VX400 Pro, VX600 Pro and VX1000 Pro can drive screens up to 10,240 pixels wide or 8,192 high, and the VX2000 Pro up to 16,384 wide, as long as the total stays within the loading capacity. All of them accept 4K at 60 Hz with 10 and 12-bit colour on their HDMI 2.0 input. They also have 10G fibre ports for long runs or a fibre converter at the screen, a USB port for playing media straight from a memory stick, and up to 256 presets. Only the VX2000 Pro has HDR, mosaic inputs and fade transitions between presets. Check the exact inputs on your model's specification sheet.

Three ways to control it

  • Front panel: a knob, a screen and buttons for layers, sources and presets. Everything essential can be done here.
  • Unico: NovaStar's control software for Windows and macOS, also available as a web page served by the processor itself. Type the IP address shown on the processor's home screen into a browser on the same network. Unico is the easiest way to map screens, build layers and manage presets.
  • NovaLCT: NovaStar's Windows software for receiving cards, calibration and Ethernet port backup, connected by USB or network. The VICP app gives simple control from a phone or tablet.

Pick one tool for each job. Settings made in the front panel, Unico and NovaLCT can overwrite each other. For example, configure the screen in Unico, then do not redo it on the front panel. Device backup in particular must be set up with one tool only.

What you need

  • The cabinet configuration file (.rcfgx or .NCP) for your LED cabinets, from the screen supplier
  • A laptop with the latest Unico and NovaLCT, from the NovaStar website
  • An Ethernet cable to connect the laptop to the processor's control port or network, and a USB cable for NovaLCT
  • Cat5e or Cat6 data cables for the cabinets, plus spares, and fibre modules if you are using the OPT ports (they are sold separately)
  • A drawing of the screen showing the cabinet grid and the planned data runs
  • A USB stick (FAT32) with the latest firmware, in case the unit needs updating

Choose the model and plan the ports

Two limits decide which model you need and how you cable the screen: the total loading capacity of the processor, and the capacity of each Ethernet port, which is about 650,000 pixels at 8-bit. Running the outputs at 10-bit, or at higher frame rates, reduces what each port can carry.

Example 1: a conference screen

A screen of 500 × 500 mm cabinets at 2.6 mm pixel pitch, 10 cabinets wide and 6 high:

  • Each cabinet is 192 × 192 pixels = 36,864 pixels. The screen is 1,920 × 1,152 = 2.2 million pixels.
  • One port can carry 650,000 ÷ 36,864 = 17 cabinets at most.
  • For the front panel's quick configuration, each port's cabinet count must be a whole multiple of the rows (6) or the columns (10). Splitting 60 cabinets into 5 ports of 12 (two columns each) works.
  • Five ports and 2.2 million pixels: a VX600 Pro (6 ports, 3.9 million) fits, leaving a port spare. A VX400 Pro has the pixel capacity but only 4 ports, so it would need 15 cabinets per port, which does not suit quick configuration. You could still map it by hand in Unico.
A 10 by 6 cabinet screen split into five Ethernet ports, each running two columns in a snake pattern Port 1Port 2Port 3Port 4Port 5Start
Front view: five ports of 12 cabinets each. Port 1 starts the chain at the bottom left, and each port runs up one column and down the next.

Example 2: a 4K screen

The same cabinets, 20 wide and 12 high, give 3,840 × 2,304 pixels: 8.8 million pixels and 240 cabinets. That is beyond the VX1000 Pro's 6.5 million, so it needs a VX2000 Pro (13 million pixels, 20 ports). Twenty ports of 12 cabinets each carries about 442,000 pixels per port, well within the limit.

The LED Screen Calculator works out the cabinet grid, resolution and NovaStar port routing for any screen, and the LED Data & Power Cabling Plan plans the cable runs.

Plan the layers too

Layers on the VX Pro come from a shared pool of layer resources, each the size of a 2K × 1K picture (see Build the layers). If the show needs a 4K source plus two picture-in-picture windows, that is 4 + 1 + 1 = 6 resources: the maximum on a VX400 Pro, VX600 Pro or VX1000 Pro. Anything more needs a VX2000 Pro, or a separate switcher in front of the processor.

Connect everything

Source, laptop and LED screen connected to a VX Pro Video sourceLaptopVX ProLED screen HDMI, DP, SDI or USBUSB or Ethernetinputs, layers, scalingEthernetports 1 to n
The video source feeds the inputs, the laptop connects to the control port for set-up, and the Ethernet outputs drive the cabinets.
  1. Cable the screen to your port plan. Label each data cable with its port number at both ends. Port 1 goes to the first cabinet in the chain.
  2. Connect the sources. Use the HDMI 2.0 input (or DP 1.2 or 12G-SDI on the VX2000 Pro) for 4K or high-bit-depth sources, and the HDMI 1.3 inputs for Full HD laptops and cameras.
  3. Connect the network. Plug the processor's Ethernet control port into the same network as your laptop, or straight into the laptop.
  4. Power on the screen, then the processor. Check that each Ethernet output's light flashes, and that the first cabinet on each chain shows its receiving card lights.

The front panel

Press the knob on the home screen to open the menu, turn it to move, and press to select or confirm. Changed values only take effect once you press the knob again. BACK goes back or cancels. Around the screen are the LAYER buttons, the SOURCE buttons, the PRESET button and number keys, and Fn, which you can assign to any menu function.

The home screen shows the device name and IP address, each open layer with its source and resolution, the output resolution and frame rate, brightness, the state of each Ethernet port, sync status and display state. Turn the knob for further pages showing the fibre ports and any connected fibre converter.

Lock the panel during the show. Hold the knob and BACK together to lock or unlock the front panel buttons.

Network settings

Go to Communication Settings and choose Manual to set a fixed IP address, subnet mask and gateway in the same range as your laptop, or Automatic to get one from the network. A fixed address is best for events and installations, so it is always in the same place. Then open Unico, or type the IP address into a browser, and the processor appears in the device list.

Load the cabinet settings

The receiving cards in the cabinets need the right settings for their LED modules before anything else. Without them the screen may show nothing, a scrambled picture or flicker. This is done once for each screen and saved into the cards.

Always use the supplier's cabinet file. It holds the module driver chip, scan, refresh and data settings for your exact cabinets. Sending the wrong settings can make the screen flicker or show garbage, and in the worst case damage modules.

From the front panel or Unico

  1. Import the cabinet file into the processor. In Unico, add it to the device. On the front panel, go to Screen Configuration > Send Cabinet Configuration Files, where files can also be loaded from a USB stick. The processor stores up to 64 files.
  2. Send the file to the receiving cards. Every cabinet should now show a clean image or test pattern, although the cabinets may be in the wrong places until the screen is mapped.
  3. Choose Save to RV Card so the cards keep the settings after power is removed.

In NovaLCT

Log in with User > Advanced Synchronous System User Login, open Screen Configuration, go to the Receiving Card tab, load the file, send it to the receiving cards and save. NovaLCT is also where you do pixel-level calibration and set up Ethernet port backup.

Map the screen

Mapping tells the processor where every cabinet sits and in which order the data reaches them, so the picture appears in one piece.

In Unico (recommended)

  1. Open the Screen page.
  2. Select Ethernet port 1 at the bottom of the page, then click and drag across the canvas to add its cabinets in the order the data runs. A progress bar under each port shows how much of its capacity is used.
  3. Select the next port and add its cabinets. Repeat for every port.
  4. To change the route, drag individual cabinets, or select a group and choose a quick topology in Cabinet Properties.
  5. Send the configuration to the screen and save it to the receiving cards.

Unico handles irregular shapes, gaps, mixed cabinet sizes and several separate screens on one processor. The VX2000 Pro also supports free topology, where one port can run a non-rectangular shape, with suitable receiving cards.

Quick Configuration (front panel)

For a regular rectangle of identical cabinets, go to Screen Configuration > Quick Configuration:

  1. Set Cabinet Row Qty and Cabinet Column Qty.
  2. Set Port 1 Cabinet Qty, then the other ports.
  3. Go to Data Flow (Front View) and turn the knob through the patterns, watching the screen. Choose the one where the test image is continuous, with no repeated or jumbled cabinets, and press the knob.

Quick configuration only works if port 1 carries the most cabinets, each port's count is a whole multiple of the rows or columns, every port runs the same pattern, and port 1 starts the chain.

Check it

Turn on Screen Configuration > Mapping to show each cabinet's sending unit, port and cabinet number on the screen, then use the test patterns under Display Control (pure colour, gradient and grid) to spot misplaced or faulty cabinets. The Pixel Map & Test Pattern Generator makes a numbered map of the whole screen to play from the source, which shows straight away if anything is out of place.

Save to RV Card. If the configuration is not saved to the receiving cards, the screen loses it the next time the power goes off.

Set the inputs

The input resolution is what each source sends to the processor. Getting it right is the key to a sharp picture. The processor tells each source what it accepts using EDID, so you set the resolution on the processor and the source follows.

Choose the resolution

  • Match the screen when you can. For a 1,920 × 1,152 screen, set a custom input of 1,920 × 1,152. Every source pixel then lands on one LED pixel with no scaling, which gives the crispest text.
  • Otherwise match the shape. A 16:9 screen works with any standard 16:9 resolution. For other shapes, use a custom resolution with the same aspect ratio so nothing is stretched.
  • Do not send far more than the screen can show. A 4K source on a 1,920-pixel-wide screen wastes three quarters of its detail and uses four layer resources instead of one.

Input connector capacity

Each input has a capacity setting that decides the largest resolution it accepts and how many layer resources its layers use:

CapacityStandard resolutionsCustom width up toLayer resources per layer
SL (single link)1,920 × 1,080 at 60 Hz2,0481
DL (dual link)3,840 × 1,080 at 60 Hz, or 3,840 × 2,160 at 30 Hz4,0962
4K4,096 × 2,160 at 60 Hz, or 8,192 × 2,160 at 30 Hz8,1924

Set each input to the smallest capacity that fits its source. A laptop sending 1,920 × 1,080 into the HDMI 2.0 input should use SL, not 4K, so it only takes one layer resource. If a custom resolution is wider than the capacity allows, switch the connector to the next capacity up.

Set it on the processor

  1. In Unico, open the input's properties (on the Programming page) and go to the Basic and EDID tabs. On the front panel, use Input Settings.
  2. Choose Standard to pick a resolution and frame rate from the list, or Custom to enter your own width, height and frame rate.
  3. Apply it, then check the source has picked up the new resolution. Some need their display settings changing, or the cable unplugging and replugging.

EDID files can also be exported and imported, so a tried and tested EDID can be loaded onto any input. SDI inputs follow the incoming signal and do not have a resolution setting.

Colour, HDCP and Mac sources

  • InfoFrame override forces how the processor reads a source's colour format, quantisation range, bit depth and colour gamut. Leave it on From Input unless a source looks wrong: if blacks look grey and colours washed out, try setting quantisation to Full or Limited.
  • HDCP must be on for copy-protected sources such as streaming players, Blu-ray players and many Apple devices, or they show black (Advanced Settings > HDCP Status).
  • Compatible with Mac helps Mac computers pick up custom resolutions. Turn it on if a Mac refuses the resolution you have set.

Build the layers

A layer is a window on the screen showing one input. Use layers for picture-in-picture, such as a presenter camera over full-screen slides, a lower third, or two sources side by side. Layer 1 is open by default and shows the first input.

Layer resources

The VX400 Pro, VX600 Pro and VX1000 Pro have 6 layer resources; the VX2000 Pro has 12. Each layer uses resources according to the capacity of its input connector:

Layer from an input set toUsesExample on a 6-resource model
SL (2K × 1K)1 resourceUp to six Full HD layers
DL (4K × 1K)2 resourcesThree wide layers
4K (4K × 2K)4 resourcesOne 4K layer plus two Full HD layers

The same input can feed more than one layer, and each of those layers uses resources. If a layer will not open, check how many resources are already in use.

Layer 1 filling the screen with two picture-in-picture layers on top Layer 1: slides, full screenLayer 2: cameraLayer 3: logo in frontat the back Initial X, Initial Y Each layer has an input sourcea size (H Width, V Height)a position (Initial X, Initial Y)a priority (higher is in front)an optional input cropa resource cost (1, 2 or 4)
Layers stack by priority. Positions are measured in pixels from the top left corner of the screen.

In Unico

  1. Open the Programming page. The inputs are listed on the left.
  2. Drag an input onto the screen to create a layer. Drag an input onto an existing layer to change its source.
  3. Drag and resize the layer with the mouse, or type exact values on the layer's Basic and Advanced tabs: width, height, position, aspect ratio, crop and priority.
  4. Rename layers so the operator knows what each one is for.

On the front panel

  1. Press a LAYER button. It flashes and the layer settings open.
  2. Press a SOURCE button to choose its input, or set Input Source in the menu.
  3. Set the Scaling Mode, then for a custom layer the size (H Width, V Height) and position of its top left corner (Initial X, Initial Y) in pixels.
  4. Set the Priority with Up, Down, Top or Bottom. A higher number sits in front.

Work out layer sizes

Keep each layer the same shape as its source to avoid stretching. A 16:9 camera in a window 640 pixels wide is 640 × 9 ÷ 16 = 360 pixels high. To sit 40 pixels in from the right edge of a 1,920-pixel-wide screen, its Initial X is 1,920 − 640 − 40 = 1,240. Positions can be negative or extend beyond the screen, so a layer can be partly off-screen on purpose.

Scale the picture

Scaling decides how a source fits its layer. The VX Pro uses NovaStar's SuperView III engine, which scales up or down by any amount.

Full screen, pixel to pixel and custom scaling modes compared Full ScreenPixel to PixelCustom Source stretched or squeezedto fill the whole screen Source shown at its own size,from the top left corner You set the layer size andposition; the source fits it
The same source in each scaling mode. The dark area is the screen, the coloured area is the picture.
ModeWhat it doesUse it for
Full ScreenScales the source to fill the whole screen, whatever its shapeA source set to the screen's resolution or aspect ratio. With a different shape, the picture is stretched.
Pixel to PixelShows the source at its own size, with no scalingThe sharpest result, especially for text, when the source matches the screen.
CustomScales the source to the layer size and position you setPicture-in-picture, letterboxing, or placing content on part of the screen.

Crop the input

Input Crop takes a rectangle from the source and shows only that, set by width, height and the position of its top left corner within the source. Use it to:

  • Remove black bars a source has added
  • Take one part of a larger canvas from a media server, for example when one 4K output feeds several screens
  • Combine with Pixel to Pixel to take an exact area of the source with no scaling at all

Fitting 16:9 content to another shape

  1. Make content at the screen's resolution. Always the best result: give content creators the exact pixel size.
  2. Letterbox or pillarbox with a custom layer that keeps the 16:9 shape. On a 1,920 × 1,152 screen, a 16:9 layer 1,920 wide is 1,080 high; set Initial Y to (1,152 − 1,080) ÷ 2 = 36 to centre it.
  3. Crop to fill: crop the source to the screen's shape, then scale it to full screen. Nothing is stretched, but the edges are lost.

The Content Scaling Calculator works out scale factors, bars and cropping for any source and screen.

Avoid stretching. Audiences notice squashed faces and oval logos immediately. If the source and screen are different shapes, use a custom layer or a crop rather than Full Screen.

OSD, USB playback and audio

OSD (on-screen display)

The OSD puts text or an image on top of everything else, always at the front. Text OSD can show static text, the time, weather and scrolling text, set up in Unico, with up to four text presets. Image OSD shows a logo or graphic (PNG, JPG or BMP) from a 75 MB gallery, positioned where you want it. Text and image OSD cannot be on at the same time.

USB playback

The USB 3.0 port plays images and videos (including MP4 with H.264 or H.265) straight from a memory stick, with no computer. Go to USB Playback to build a playlist, choose loop, play in order or repeat one, and set image durations and transitions. USB playback appears as an input that can be put on a layer, which makes it a useful backup if the main source fails, or a simple way to run a holding slide or sponsor loop.

Audio

The processor can pass audio from a layer's source, the embedded audio of an input or the 3.5 mm audio input to its audio output, with volume control (Advanced Settings > Audio). It is handy for simple installations; at events, take audio from the source or switcher to the sound system instead.

Brightness, colour and output

Brightness

Screen Brightness sets the overall level. Indoor screens are usually much brighter than needed at full brightness: start around 20 to 40% indoors and adjust by eye from the audience, and higher outdoors in daylight. Lower brightness is kinder to the audience and to cameras, and cuts power and heat. Dimming does reduce the grey levels the screen can show; the LED Greyscale & Dimming Calculator shows how much.

Colour and bit depth

  • Screen Configuration > LED Screen Color sets the gamma (default 2.8) and colour temperature (standard, cool, warm or custom red, green and blue). Match the white point to the room lighting or to other screens.
  • Unico's Screen Settings page has image quality adjustments for the whole screen.
  • Set Output Bit Depth chooses 8-bit or 10-bit output. 10-bit gives smoother gradients with suitable receiving cards and sources, but reduces port capacity, so plan for it from the start. HDR on the VX2000 Pro needs 10-bit.

Frame rate, sync and latency

  • Advanced Settings > Synchronization sets the output timing: Internal (60 Hz by default, adjustable), locked to an input, or Genlock. For filming and broadcast, match the camera system (for example 50 Hz in the UK) and lock to genlock. Every processor feeding one screen must use the same sync source.
  • Low Latency takes about a frame off the delay through the processor. Auto sets it according to the screen layout. Useful for IMAG (live camera close-ups of the presenter), where any delay is noticeable.
  • The LED Filming & Camera Settings and LED Refresh Rate & Scan Checker tools help avoid banding and flicker on camera.

Working modes

Device Working Mode offers Video Controller (normal use), Fiber Converter (the unit sits at the screen, taking fibre from another processor and driving its Ethernet ports) and ByPass (a plain sending card with no scaling or layers, for the lowest delay).

Presets and show control

A preset stores the layer layout: which layers are open, their sources, sizes, positions, priorities and crops. The VX Pro stores up to 256 presets.

  1. Build the look, then save it to a preset: in Unico, or on the front panel under Preset Settings > Save. Saving over a preset replaces it.
  2. Name presets clearly in Unico ("Walk-in", "Slides + camera", "Full camera", "Sponsors"), so anyone can run the show.
  3. Recall a preset during the show by pressing PRESET and its number on the front panel, from Unico, or from the VICP app.

Changes between presets are a straight cut. The VX2000 Pro can also fade, over 1 to 3 seconds.

Display control

Display Control switches the screen between Normal, Freeze (hold the current frame) and FTB (fade to black), and shows test patterns. Freeze the screen while a presenter's laptop is changed or restarted, so the audience never sees a desktop or "no signal". Standby Mode blacks the screen, mutes the audio and locks the panel, for breaks in an installation.

Backup and redundancy

  • Input backup pairs a main and a backup input with the same capacity. If the main source is lost, the processor switches automatically, and with Primary Source Preferred it switches back when the main source returns. A USB playback loop makes a good last-resort backup.
  • Ethernet port backup runs a cable from a spare port to the far end of each cabinet chain, so a broken cable part-way along does not black out the cabinets after it. Set it up in NovaLCT, or in Unico's Cabinet Properties.
  • Fibre copy and backup: the spare OPT ports can copy or back up the Ethernet outputs (OPT Mode), for a second screen or a redundant fibre path.
  • Device backup uses a second processor of the same model and firmware as a hot spare on the same network, with its data feeding the other end of each chain.
  • Restore points: once everything works, save the configuration (up to five restore points), and export a copy to your laptop. A replacement unit can be set up in minutes.

Final checks

  • Cabinet settings and mapping saved to the receiving cards, and the screen checked after a full power cycle
  • All Ethernet ports showing data on the home screen, and port backup tested by unplugging a main cable
  • Test patterns showing a continuous image with no misplaced, missing or flickering cabinets
  • Each source at its intended resolution and connector capacity, with nothing stretched
  • Layer resources checked for the busiest look in the show
  • Presets saved, named and tested, with a list for the operator
  • Brightness set from the audience, and checked on camera if the event is filmed
  • Input backup and the USB fallback tested
  • Restore point saved and exported, and the front panel locked

Troubleshooting

ProblemLikely causesThings to try
Screen completely blackNo cabinet settings, display set to FTB or standby, brightness at 0, no data on the portsCheck Display Control, standby and brightness, check the port lights, show a test pattern, and resend the cabinet file.
Test pattern works but no pictureNo signal, wrong layer source, HDCPCheck the input status, choose the right source for the layer, and turn on HDCP for that input.
A layer will not openNot enough layer resources leftClose unused layers, or drop inputs to a smaller capacity (4K to DL or SL).
Source will not take the custom resolutionWider than the connector capacity, source not reading the new EDID, Mac compatibilityRaise the connector capacity, replug or restart the source, and turn on Compatible with Mac for Macs.
Cabinets in the wrong places or jumbledWrong mapping or data flow, cables in the wrong portsTurn on Mapping, check the cables against the plan, and correct the route in Unico.
Cabinets dark from one point onwardsFaulty data cable or receiving card at that pointSwap the cable into the first dark cabinet, then its receiving card. Port backup prevents this taking out the rest of the chain.
Flicker or scrambled modules on some cabinetsWrong or mixed cabinet settings, cabinets from a different batchResend the correct cabinet file to all cards and save to the receiving cards.
Settings lost after power offNot saved to the receiving cardsRedo the settings and use Save to RV Card.
Picture stretched, soft or text shimmeringSource and screen different shapes, heavy scalingSet the source to the screen resolution and use Pixel to Pixel, or a custom layer with the right aspect ratio.
Washed-out blacks or odd coloursQuantisation range mismatchChange the input's InfoFrame quantisation between Full and Limited.
Banding or flicker on cameraFrame rate not matched to the camera, very low brightnessMatch the output frame rate to the camera, use genlock, and avoid very low screen brightness.
Unico or the browser cannot find the processorDifferent IP range, network blockedCheck Communication Settings and put the laptop in the same range, or connect directly.

Firmware and factory reset

To update the firmware, copy the .img file to the root of a FAT32 USB stick, insert it in the rear USB port and use System Settings > Update Device. Do not power off or touch anything while it updates. Read the release notes first, as updates can change menus and features.

Factory Reset offers Save IP, Keep User Data (keeps EDIDs, network settings, imported files and restore points) and Reset All. Save a restore point first. A reset does not change the settings stored in the receiving cards.

Back to top