All guides
viewhub.stream · How-to Guides

Video Signals and Connectors Compared

HDMI, DisplayPort, USB-C, SDI, DVI, VGA, composite and more: what each carries, cable lengths, and when to use which

10 min readUpdated

Contents

Before you start

A video signal can travel in many different ways: an old yellow phono lead, a VGA cable, HDMI, DisplayPort, USB-C, a BNC cable carrying SDI, a network cable or a strand of fibre. Each was designed for a different job, and each has its own limits on resolution, cable length, audio, locking connectors and copy protection. Choosing the right one avoids most of the "no signal", dropout and compatibility problems in AV. This guide compares the common video signals, their connectors and their practical limits, and explains when you would choose one over another.

Cable lengths are typical, not guaranteed. The maximum reliable length depends on the resolution and frame rate, the quality of the cable, and the equipment at each end. Higher resolutions always mean shorter passive cables. Treat the figures here as a guide, and test long runs before relying on them.

The connectors at a glance

Simplified front views of common video connectors HDMItype ADisplayPortone corner cutUSB-CreversibleRJ45HDBaseT, AV over IPDVI-Ddual link shownVGA15-pin D-subBNCSDI, compositeRCA phonocomposite (yellow)
Simplified views of the common video connectors (not to scale).
SignalTypeConnectorAudioTypical maximumTypical reach
Composite (CVBS)AnalogueRCA phono (yellow) or BNCNo (separate)Standard definition (576i)Tens of metres on good coax
S-VideoAnalogue4-pin mini-DINNoStandard definitionUp to about 15 to 30 m
Component (YPbPr)Analogue3 × RCA (green, blue, red) or BNCNo1080i, some 1080pTens of metres on good coax
VGA (RGBHV)Analogue15-pin D-sub (HD15)NoUp to about 1,920 × 1,200 in practiceAbout 5 to 15 m before softening
SCARTAnalogue21-pin SCARTYesStandard definitionA few metres
DVIDigital (DVI-I also analogue)DVI-D or DVI-INot usually1,920 × 1,200 single link; 2,560 × 1,600 dual linkAbout 5 m at full resolution
HDMIDigitalHDMI type A (also mini and micro)Yes, multichannel4K to 10K depending on versionAbout 3 to 5 m at 4K 60 Hz passive
DisplayPortDigitalDisplayPort or Mini DisplayPortYes4K to 16K depending on versionAbout 2 to 3 m at the highest rates
USB-C (DP Alt Mode, Thunderbolt)DigitalUSB-CYesAs DisplayPortAbout 1 to 2 m passive at full speed
SDIDigitalBNC (75 Ω)Yes, up to 16 channels embedded1080p (3G) to 4K 60 (12G)About 70 to 100 m (3G), less for 12G
HDBaseTDigital extensionRJ45 over Cat6Yes4K 30 Hz (more with compression)Up to 100 m
FibreDigital extensionLC, SC or HDMI/SDI fibre unitsYesDepends on the systemHundreds of metres to many kilometres
AV over IPDigital networkRJ45 or fibre to a network switchYesDepends on the system and network speedAnywhere on the network

Analogue video

Analogue signals carry the picture as a continuously varying voltage. They degrade gradually over distance (getting softer, noisier or smeared) rather than failing suddenly, and they have no copy protection or handshaking, so they "just work" when connected. Their resolution is limited, and they are now mainly found on older equipment.

Composite (CVBS)

  • The whole picture, brightness and colour combined, on one wire. Usually a yellow RCA phono plug, or BNC in professional kit.
  • Standard definition only (576i in PAL countries such as the UK). Colours bleed and fine detail shimmers.
  • Use it for: older cameras, CCTV, legacy equipment and simple monitoring where quality does not matter.

S-Video

  • Separates brightness (Y) and colour (C) on two wires in a small 4-pin connector, giving a cleaner picture than composite.
  • Standard definition only. Found on older camcorders, computers and AV equipment.

Component (YPbPr)

  • Three separate signals on three cables (green, blue and red plugs). Supports high definition up to 1080i, and 1080p on some equipment.
  • Runs well over good 75 Ω coaxial cable. It was common on older projectors, DVD players and games consoles.
  • Do not confuse the red component plug with the red audio plug: component carries no audio.

VGA

  • The analogue computer connection: a 15-pin D-sub carrying separate red, green, blue and sync signals.
  • Handles computer resolutions up to around 1,920 × 1,200 in practice, but the picture softens and ghosts on long or poor cables. Good-quality cable with individual coaxial cores reaches further.
  • No audio. Still found on older projectors, displays and some servers.
  • Use it for: connecting legacy equipment. Convert to digital with an active converter where possible.

SCART

A 21-pin European connector carrying composite, S-Video or RGB video plus stereo audio and switching signals in one plug. Mostly found on older televisions, VCRs and set-top boxes.

DVI

DVI (Digital Visual Interface) was the first common digital computer display connection, and the video signal is the same as early HDMI.

  • DVI-D is digital only. DVI-I also carries analogue VGA signals, so a passive adaptor can convert it to VGA. DVI-A is analogue only and rare.
  • Single link reaches 1,920 × 1,200 at 60 Hz; dual link (with more pins) reaches 2,560 × 1,600.
  • Normally no audio, although some graphics cards send audio through DVI to an HDMI adaptor.
  • Screw locks keep it in place, which is useful in racks and control rooms.
  • About 5 m is reliable at full resolution; longer runs need active cables or extenders.
  • Use it for: older computers and displays, and some LED processors and video wall controllers. HDMI to DVI adaptors work passively for video, but not audio.

HDMI

HDMI (High-Definition Multimedia Interface) is the standard connection for televisions, projectors, displays, set-top boxes, games consoles, cameras and most AV equipment.

VersionBandwidthTypical capabilityCable to use
HDMI 1.3 and 1.410.2 Gbps1080p at 60 Hz, 4K at 30 HzHigh Speed
HDMI 2.018 Gbps4K at 60 Hz (HDR with 4:2:2 or 4:2:0)Premium High Speed
HDMI 2.148 Gbps4K at 120 Hz, 8K, full HDRUltra High Speed
  • Carries: video, multichannel audio, CEC (control between devices), ARC and eARC (audio back from the TV to a soundbar or receiver) and HDCP copy protection.
  • Connectors: type A (standard) on most equipment, type C (mini) and type D (micro) on cameras and small devices. Standard HDMI has no lock, so plugs work loose; use locking cables or cable supports in permanent installations.
  • Lengths: passive cables are reliable to about 3 to 5 m at 4K 60 Hz, and further at 1080p. Active copper cables reach 15 to 30 m; optical HDMI cables (AOC) 100 m or more.
  • Use it for: almost all consumer and AV equipment. The default choice for short connections.
  • Watch out for: EDID and HDCP handshaking problems with switchers, splitters and extenders. See HDMI and Video Signal Troubleshooting.

DisplayPort

DisplayPort is the computer industry's display connection, found on graphics cards, laptops, computer monitors and some professional displays and video wall controllers.

VersionMaximum bandwidthTypical capability
DisplayPort 1.221.6 Gbps4K at 60 Hz
DisplayPort 1.432.4 Gbps4K at 120 Hz, 8K at 60 Hz with compression (DSC)
DisplayPort 2.1Up to 80 Gbps8K and beyond, high refresh rates
  • Locking latch on the full-size connector holds it firmly. Press the button to release.
  • Multi-Stream Transport (MST) can daisy-chain several monitors from one port.
  • Adapting to HDMI: most DisplayPort outputs are "dual-mode" (marked DP++), so a cheap passive adaptor works. Without DP++, or for 4K 60 Hz HDMI, use an active adaptor.
  • Lengths: about 2 to 3 m at the highest data rates, further at lower resolutions; active and optical cables reach much further.
  • Use it for: computers to monitors, high-refresh displays, multi-monitor desks and some video wall processors. It is uncommon on televisions and AV equipment.

USB-C and Thunderbolt

Many laptops, tablets and phones send video over USB-C, usually as a DisplayPort signal (DisplayPort Alternate Mode), or through Thunderbolt.

  • Not every USB-C port carries video. Look for the DisplayPort or Thunderbolt symbol next to the port, or check the device's specification.
  • One cable for everything: a USB-C connection can carry video, audio, USB data and power to charge the laptop, which makes it ideal for meeting room tables and docking stations.
  • Cables matter: many USB-C cables only carry charging and slow data. Use cables rated for video (USB 3.x or Thunderbolt, marked with their speed). Passive cables at full speed are short, about 1 to 2 m; longer runs need active or optical cables.
  • Use it for: laptops at desks and meeting room tables, and docking stations.

SDI

SDI (Serial Digital Interface) is the professional broadcast and live production standard. It sends uncompressed video over a single 75 Ω coaxial cable with locking BNC connectors.

StandardData rateTypical formatTypical reach on good cable
SD-SDI270 MbpsStandard definitionAround 300 m
HD-SDI1.5 Gbps720p and 1080iAround 100 to 140 m
3G-SDI3 Gbps1080p at 50 or 60 HzAround 70 to 100 m
6G-SDI6 Gbps4K at 30 HzShorter than 3G
12G-SDI12 Gbps4K at 50 or 60 HzAround 50 to 70 m, with high-grade cable
  • Advantages: locking connectors, long cable runs, no handshaking (connect it and it works), embedded audio (up to 16 channels) and timecode, and simple distribution with amplifiers and routers.
  • No copy protection: SDI does not carry HDCP, so protected content cannot be sent over it.
  • Cable: use 75 Ω cable rated for the SDI speed you are running; ordinary or 50 Ω coax shortens the reach dramatically. Fibre extends SDI to kilometres.
  • Use it for: cameras, broadcast, live events, streaming productions, and long runs to LED processors and projectors.

Extending the signal: HDBaseT, fibre and AV over IP

HDBaseT

  • Sends HDMI video, audio, control (RS-232, IR), Ethernet and often power over a single Cat6 cable, up to 100 m.
  • Point to point between a transmitter and receiver, not through a network switch.
  • Most systems carry up to 4K at 30 Hz uncompressed, or 4K at 60 Hz with chroma subsampling or light compression.
  • Use it for: projectors and displays a long way from the source in installations, and wall plates in meeting rooms. Use good-quality solid-core Cat6 or better, and avoid joints.

Fibre

  • HDMI, DisplayPort and SDI fibre extenders and optical cables carry full bandwidth hundreds of metres to many kilometres.
  • Immune to electrical interference and ground loops, and thin and light.
  • Use it for: very long runs, between buildings, outdoor events, broadcast, and electrically noisy environments. Handle carefully: fibre must not be bent tightly or crushed, and connectors must be kept clean.

AV over IP

  • Encoders turn video into network data, and decoders turn it back into video, over a standard network switch, so any source can be routed to any display.
  • Systems running on 1 Gb networks use compression with a little latency; 10 Gb systems use very light or no compression for near-zero latency.
  • Common systems and standards include SDVoE, NDI, Dante AV, IPMX and, in broadcast, SMPTE ST 2110.
  • Use it for: large or growing systems, many sources and displays, campuses and venues. It needs a properly designed network with the right switch features.

The Network Cable Reach Calculator, Fibre Link Budget Calculator and Video Bandwidth & Storage Calculator help plan extensions.

Cable lengths compared

Typical maximum cable lengths for each signal type at common resolutions 1 m10 m100 m1 km10 kmComposite on coaxVGA (1080p)DVI (1920 × 1200)HDMI passive (1080p)HDMI passive (4K 60)HDMI active copperHDMI opticalDisplayPort (highest rates)USB-C passive (full speed)HDBaseT over Cat63G-SDI on coax12G-SDI on coaxFibre
Typical reliable lengths on good-quality cable, on a logarithmic scale. Higher resolutions and poorer cables reduce the reach.

Choosing the right signal

SituationUsually bestWhy
Short connection between AV equipmentHDMIUniversal, carries audio and control
Computer to monitor, high refresh rate or several monitorsDisplayPortHigh bandwidth, locking, MST daisy-chaining
Laptop at a meeting table or deskUSB-CVideo, USB and charging in one cable
Cameras and live productionSDILocking, long runs, no handshaking, embedded audio
Display or projector up to 100 m away in an installationHDBaseTOne network-type cable with power and control
Very long runs, between buildings, outdoorsFibreKilometres of reach, immune to interference
Many sources to many displays, flexible routingAV over IPScalable over a network
Older equipmentVGA, composite or component, converted to digitalCompatibility
Protected content (streaming, Blu-ray)HDMI or DisplayPort with HDCP throughoutSDI and many capture devices do not carry HDCP

Adaptors and converters

From → toWhat you needNotes
HDMI ↔ DVI-DPassive adaptor or cableVideo only; no audio
DisplayPort (DP++) → HDMIPassive adaptorUse an active adaptor for 4K 60 Hz or if the port is not DP++
USB-C → HDMI or DisplayPortUSB-C adaptor or cableThe port must support video; check the resolution the adaptor supports
HDMI or DisplayPort → VGAActive converterConverts digital to analogue; passive cables do not work
VGA, composite or component → HDMIActive converter or scalerDigitises and usually scales to a modern resolution
HDMI ↔ SDIActive converterCommon in production; HDMI to SDI cannot carry HDCP-protected content
DVI-I → VGAPassive adaptorOnly DVI-I carries the analogue pins; DVI-D does not
  • Every adaptor is a possible failure point. Use as few as possible, especially in long runs and permanent installations.
  • Audio: when converting from HDMI to a format without audio (DVI, VGA), take the audio out separately with an audio de-embedder or from the source's headphone or line output.
  • Scaling: a scaler converts the resolution and frame rate as well as the connector, useful when an older source has to feed a modern display or processor.
Back to top