Before you start
An LED screen that looks perfect to the audience can look terrible on camera: dark bands rolling through the picture, flicker, a shimmering rainbow pattern, or colours that shift as the camera moves. These problems come from the way LED screens and cameras both work in rapid slices of time. With the right screen, processor and camera settings, they can almost always be avoided. This guide explains the causes and the fixes, for live events with image magnification (IMAG), streaming, broadcast and video production.
| Problem | What you see | Main causes |
|---|---|---|
| Scan lines and banding | Dark horizontal bands, often rolling up or down | Low refresh rate, camera shutter not matched to the screen, frame rate mismatch |
| Flicker | The screen brightness pulses | Frame rate mismatch between screen and camera, low refresh at low brightness |
| Moiré | Shimmering rainbow or wavy patterns | The screen's pixel grid interfering with the camera sensor's grid |
| Colour shift | Colours change towards the edges or as the camera moves | Viewing angle of the LEDs, camera off-axis |
| Crushed or noisy blacks | Banding in dark gradients, blotchy shadows | Screen run at very low brightness with limited greyscale |
Why it happens
An LED screen does not light every pixel continuously. Each module lights its rows in turn (scanning) and switches LEDs on and off very rapidly to create different brightness levels (PWM). The refresh rate is how many times a second this whole cycle repeats. Our eyes blend it into a steady image, but a camera captures each frame in a short slice of time. If that slice does not contain a whole number of refresh cycles, some rows are caught brighter than others, which shows up as bands.
Choose the right screen
- Refresh rate: 3,840 Hz is the usual minimum for screens that will be filmed; 7,680 Hz or more for broadcast, virtual production and high-frame-rate or high-shutter-speed work. 1,920 Hz screens often band on camera.
- Driver chips and greyscale: screens with good driver chips keep a high refresh rate and smooth greyscale at low brightness. Ask the supplier for the refresh rate at the brightness you will actually use.
- Pixel pitch: finer pitches are less prone to moiré at a given camera distance, and allow tighter shots.
- Viewing angle and colour consistency: important when cameras look at the screen from the side, and for curved screens.
- Black surface and contrast: improves the image under stage lighting.
The LED Refresh Rate & Scan Checker checks a screen's refresh and scan against a camera's settings.
Match the frame rates
The single most important step is to run the screen at the same frame rate as the cameras, or an exact multiple of it, and lock them together.
- Agree the production frame rate before the event. In the UK, broadcast and most streaming use 50 Hz (25 or 50 frames per second). Cinema and some productions use 24 or 23.98; US-standard productions use 29.97, 30, 59.94 or 60.
- Set the LED processor's output frame rate to match: for example 50 Hz for a 25 or 50 fps production.
- Lock to genlock. Feed the production's reference signal (tri-level or black burst) to the LED processor, and set its sync to genlock, so the screen's frames are timed exactly with the cameras'. Every processor driving the same screen must use the same sync.
- Send matching sources: media servers and switchers feeding the screen should run at the same rate, so frames are not dropped or repeated.
Mixed frame rates cause flicker. A screen at 60 Hz filmed at 50 fps (or the other way round) will show slow rolling bands or pulsing, whatever the shutter speed. Fix the frame rate first.
Camera settings
Shutter speed
- Use a shutter speed that is a whole fraction of the screen's frame period. At 50 Hz, 1/50 or 1/100 work well; at 60 Hz, 1/60 or 1/120.
- The common "180° shutter" (half the frame period: 1/50 at 25 fps, 1/100 at 50 fps) usually works if the screen's refresh rate is high.
- Very fast shutter speeds (1/500 and above, for sport or slow motion) need a very high refresh rate screen and may still show banding.
- If the camera has a fine shutter adjustment (such as clear scan or synchro scan), adjust it slowly while watching the screen until banding disappears.
Exposure and colour
- Expose for the screen. The screen is often much brighter than the people in front of it. Reduce the screen's brightness rather than closing the camera's iris so far that the presenter is underexposed. A screen at 20 to 40% brightness is often right for camera.
- Match white balance. Set the screen's colour temperature to suit the lighting, often around 5,600 K for daylight-balanced lighting or 3,200 K for tungsten, and set the cameras to match.
- Use a waveform monitor to keep the screen out of clipping on camera.
The LED Filming & Camera Settings tool suggests shutter speeds and frame rates for your screen and camera.
Avoid moiré
Moiré appears when the regular grid of LED pixels lines up with the regular grid of pixels on the camera's sensor, creating a new, shimmering pattern. It depends on the pixel pitch, the camera distance, the lens and the focus.
- Move the focus off the screen. Focus on the presenter in front of it; a slightly soft screen rarely shows moiré.
- Change the distance or zoom. Moiré appears at particular sizes of the pixel grid on the sensor. Moving the camera or zooming slightly usually makes it vanish.
- Use a shallower depth of field (wider aperture) to soften the screen.
- Change the angle: shooting slightly off square to the screen breaks up the pattern.
- Choose a finer pitch where cameras will be close to the screen. The Camera Field of View Calculator helps check how much of the screen fills the frame.
IMAG, streaming and virtual production
Image magnification (IMAG)
When cameras show the presenter on the LED screen behind them, any delay is obvious as lips and voice drift apart. Keep the chain short: use low-latency modes on the cameras, switcher and LED processor (see the low latency settings in the VX Pro guide), avoid unnecessary scaling and frame-rate conversion, and add audio delay if needed to match the picture.
Streaming
For a stream, the screen behind the presenter is part of the shot. Lower the screen brightness, check the shot on a monitor fed from the actual stream output, and feed the stream a clean copy of the screen content where possible, so remote viewers see slides sharply rather than through the camera.
Virtual production and XR
Virtual production stages use LED walls as live backgrounds that move with the camera. They need very high refresh rates, genlock throughout, low latency, careful colour calibration, and specialist processing that can show different images to different cameras or to the camera and the audience. This is a specialist field: work with experienced suppliers.
Camera checklist
- Screen refresh rate suitable for filming (3,840 Hz or higher)
- Production frame rate agreed, and the LED processor set to match
- Genlock connected to every LED processor and camera system
- Sources and media servers running at the production frame rate
- Camera shutter set to a matching speed, fine-tuned if needed
- Screen brightness reduced for camera, with white balance matched
- Moiré checked at every camera position and focal length
- Latency checked end to end for IMAG
- Everything tested on the actual cameras before the event