All guides
viewhub.stream · How-to Guides

100 V Line Speaker Systems: Design, Wiring and Testing

Choose taps, size amplifiers and cable, add zones, volume controls and paging, and test and fault-find

10 min readUpdated

Contents

Before you start

A 100 V line system lets one amplifier drive dozens of loudspeakers spread across a building, on long runs of thin cable, with the level of each speaker set by a simple tap. It is the standard way to wire background music and paging in shops, offices, schools, hotels, factories and stations. It is also the basis of voice alarm systems, which have their own rules.

This guide explains how 100 V line works, how to design a system, choose taps, size amplifiers and cable, add zones, volume controls and paging, and how to test and fault-find. In some countries the same system runs at 70 V; the principles are identical.

100 V line carries a hazardous voltage. At full power the line runs at up to 100 V RMS, with higher peaks. Make and break connections with the amplifier off or muted, use terminals and enclosures that keep fingers away from live parts, and treat the wiring with the same care as mains.

How 100 V line works

A normal amplifier drives a few low-impedance speakers (4 or 8 Ω) with high current at a low voltage. That current means thick cable, short runs and only a few speakers per channel. A 100 V line amplifier instead delivers its full power at a high voltage (100 V) and a low current, which travels efficiently down thin cable.

Each loudspeaker has a small transformer that steps the 100 V back down to suit the speaker. The transformer has several taps, each drawing a different amount of power from the line: for example 0.75, 1.5, 3 and 6 W. All the speakers connect in parallel across the same pair of cables.

A 100 V line amplifier feeding several speakers in parallel, each on its own tap 100 V amplifier100 W channel+ 100 VCOM6 W3 W3 W1.5 W3 WTotal load: 6 + 3 + 3 + 1.5 + 3 = 16.5 W, line impedance 10,000 ÷ 16.5 ≈ 606 Ω
Every speaker connects across the same two wires. Each one's tap sets how much power it takes, and the taps add up to the load on the amplifier.

The maths

Power, voltage and impedance are related by P = V² ÷ Z. On a 100 V line:

  • A speaker tapped at P watts presents an impedance of 10,000 ÷ P ohms. A 6 W tap is 1,667 Ω; a 1.5 W tap is 6,667 Ω.
  • The whole line presents 10,000 ÷ total watts. Twenty speakers at 3 W (60 W) present about 167 Ω.
  • On a 70 V line, use 4,900 instead of 10,000.

So you never need to calculate impedances to design a system: just add up the taps.

Advantages and limits

  • Advantages: many speakers on one amplifier channel, long runs, thin cable, easy level setting per speaker, simple expansion, and easy zoning and volume control.
  • Limits: transformers restrict deep bass and add a little distortion at high power, and every speaker on a line plays the same programme. For premium music, use low-impedance speakers, a subwoofer, or both.

Design the system

  1. Lay out the speakers for the coverage you need. See How to Set Up Background Music for spacing.
  2. Choose taps for each speaker based on the level needed in that area (see below).
  3. Group speakers into zones by use: each zone usually gets its own amplifier channel or a volume control.
  4. Add up the taps in each zone.
  5. Choose the amplifier with headroom over the total.
  6. Size the cable for each run.
  7. Add volume controls, priority and paging where needed.

Choosing taps

Each halving of tap power lowers the level by 3 dB. As a starting point:

AreaTypical tap
Toilets, corridors, small offices0.75 to 1.5 W
Shops, restaurants, open offices with normal ceilings1.5 to 3 W
Noisy areas, high ceilings, louder music3 to 6 W
Warehouses, factories, outdoor areas, horn speakers10 W or more

To check, work out the level each speaker produces: sensitivity (dB at 1 W, 1 m) + 10 × log₁₀(tap watts) − 20 × log₁₀(distance in metres). A ceiling speaker of 89 dB sensitivity on a 3 W tap, heard 1.8 m below, gives about 89 + 4.8 − 5.1 ≈ 89 dB, plenty for background music, with room for paging. The Speaker Coverage & SPL Calculator does this for you.

Leave room to go up. Choose taps that give the level you need with the amplifier around three-quarters of the way up, not at full power. It is easy to turn a system down, but changing taps on dozens of speakers in a finished ceiling is a lot of work.

Sizing the amplifier

Add up all the taps on the channel and allow at least 20 to 25% headroom. Twenty speakers at 3 W is 60 W; × 1.25 = 75 W, so use a 100 W channel. The headroom covers cable losses, transformer losses and peaks, and leaves room to add a few speakers later. Do not load an amplifier beyond its rating: it will clip, overheat or shut down.

The 100V / 70V Line Designer adds up the taps, checks amplifier headroom and estimates cable loss.

Size the cable

Even at 100 V some power is lost in the cable. Keep the loss under about 10% (roughly 0.5 dB), and less for long or important runs.

  1. Work out the line impedance: 10,000 ÷ total watts. For 60 W, that is 167 Ω.
  2. Work out the cable resistance there and back: 2 × length × resistance per metre. For 1.5 mm² copper, about 0.0115 Ω per metre per core; a 200 m run is 2 × 200 × 0.0115 ≈ 4.6 Ω.
  3. The loss is roughly cable resistance ÷ (line impedance + cable resistance): 4.6 ÷ 171.6 ≈ 2.7%. Fine.

The heavier the load, the lower the line impedance and the bigger the loss, so long runs with lots of speakers may need larger cable. In practice, 1.5 mm² two-core cable suits most background music circuits, and 2.5 mm² suits long or heavily loaded runs. The Speaker Cable Size Calculator checks any run.

Cable type

  • Use cable suitable for the installation: LSZH (low smoke, zero halogen) in public buildings, and in containment or clipped neatly.
  • Voice alarm circuits must use fire-resistant cable (such as enhanced fire-resistant types to BS 8434 or BS EN 50200), typically red, routed and fixed to the voice alarm standard.
  • Keep speaker lines away from data and microphone cables, or at least cross them at right angles.
  • Label each circuit at the amplifier and at junction boxes.

Wiring and connections

  • Connect every speaker in parallel, with the same polarity: + of the line to the + (or 100 V) terminal, and − to the common (COM or 0 V). Mixed polarity thins out the sound where speakers overlap.
  • Use the correct tap. Tap terminals are marked with the power, or a rotary switch on the speaker selects it. Some speakers have an 8 Ω (bypass) setting for low-impedance use: never use it on a 100 V line.
  • Use a ceramic terminal block or the speaker's own terminals, with secure connections. Loose connections cause crackles, intermittent faults and heat.
  • Loop through from speaker to speaker (daisy chain), or branch from junction boxes. Both are fine electrically. For voice alarm, follow the specified wiring arrangement.
  • Do not mix voltages. A 100 V speaker on a 70 V line takes about half its marked tap power. A speaker designed only for 70 V on a 100 V line takes about twice its marked power and may be damaged.

Never connect a low-impedance (4 or 8 Ω) speaker directly to a 100 V line. It presents almost a short circuit, shutting down or damaging the amplifier, and the speaker itself can be destroyed. Use a line transformer to connect a low-impedance speaker.

Zones, volume controls and paging

Zones

Split the building into zones by use, so each area can have its own music, level and announcements: shop floor, café, toilets, back of house, car park. Zones are fed from separate amplifier channels, or from one channel through a zone selector that switches lines on and off.

Volume controls (attenuators)

A 100 V volume control is a transformer with a selector switch that changes the level in steps, usually about 3 dB each. It is wired between the amplifier and the speakers of its zone and must be rated for at least the total taps it controls (a 30 W control for 24 W of speakers, for example).

Priority override

Announcements and emergency messages must reach every speaker at full level, even if a local volume control is turned down or off. Priority (override) relays in the volume control bypass it when an announcement is made:

  • 3-wire systems use a separate priority line from the amplifier to switch the control to full level.
  • 4-wire systems use a separate 24 V DC signal from the paging system to operate the relay.

Check that priority works in every zone during commissioning.

A zone volume control with a priority relay that bypasses it for announcements 100 V ampmusic and pagingVolume controlsteps of about 3 dBwith priority relayZone speakersfull level during a page24 V priority signal (4-wire) or priority line (3-wire)
Normally the music passes through the volume control. When a page is made, the 24 V signal switches the relay and the speakers get full level, whatever the control is set to.

Paging

  • A paging microphone or zone paging station selects which zones receive the announcement, plays a chime first, and turns the music down automatically.
  • Pre-recorded messages (for opening and closing times, security messages) can be triggered by a timer, button or other system.
  • Paging needs even coverage for intelligibility: choose speaker spacing and taps with speech in mind.

Voice alarm is different. A system used to broadcast evacuation messages must be a voice alarm system designed, installed and maintained to BS 5839-8, with equipment to the BS EN 54 series, fire-resistant cabling, monitored lines and standby power. A background music and paging system is not a voice alarm system unless it has been designed as one.

Amplifier settings and EQ

  • High-pass filter at 80 to 100 Hz (or higher for small speakers). Line transformers can saturate at low frequencies, causing distortion and stressing the amplifier, even when the music does not sound bass-heavy. Many 100 V amplifiers have a switchable filter; use it.
  • Limiters on each channel keep the system within its design level.
  • EQ: gentle cuts in the low mids and upper mids often help in hard rooms; avoid big bass boosts on transformer speakers.
  • Input sensitivity: set it so the music source and paging microphone reach the intended level without clipping.

Test and commission

  1. Visual check: every speaker fixed securely, with safety wires where needed, correct taps set, terminals tight and polarity consistent.
  2. Measure the line impedance of each circuit with a 100 V line impedance meter, which tests at an audio frequency (usually 1 kHz). Compare it with the expected 10,000 ÷ total watts. An ordinary multimeter is no use here: transformers have a very low DC resistance.
  3. Check insulation between the cores and to earth, with the amplifier and any electronics disconnected, especially on long runs, outdoors and in damp areas.
  4. Connect the amplifier and bring the level up slowly with music, walking every zone and listening for silent, distorted or rattling speakers.
  5. Check every zone and volume control, and test paging and priority in each zone.
  6. Set and measure levels in each area, then lock the amplifier and processor settings.
  7. Record the circuits, taps, impedance readings and settings on a schematic left on site.
Impedance readingWhat it suggests
Close to the expected valueGood: taps and wiring as designed.
Much lower than expectedTaps set higher than designed, extra speakers, or a speaker on its 8 Ω bypass setting.
Very low (a few ohms)Short circuit or a low-impedance speaker on the line.
Higher than expectedSome speakers disconnected, an open circuit part-way along, or taps set lower than designed.
Very high or openBroken cable or disconnected line.

Fault-finding

ProblemLikely causesThings to try
Amplifier goes into protect or shuts downShort circuit, overload, low-impedance speaker on the line, transformer saturation from bassMeasure the line impedance, check taps, switch on the high-pass filter, split the load.
Some speakers silentBreak in the cable, loose terminal, failed speaker or transformerCheck the speakers before and after the silent ones, then the connections between them.
Whole zone silentVolume control at zero, zone switched off, cable break near the startCheck the zone selector and volume control, then measure the line impedance from the amplifier.
Crackles or intermittent soundLoose or corroded connections, damaged cableTighten and remake terminals, check junction boxes and outdoor connections.
Distortion at moderate levelsAmplifier overloaded, transformer saturation, damaged speakerReduce taps or split the load, use the high-pass filter, replace damaged speakers.
Thin soundMixed polarityCheck every speaker is wired + to + and COM to −.
Announcements quiet in one zonePriority relay not working, missing 24 V or priority wireCheck the priority wiring and the relay in the volume control.

Finding a fault on a long line

Split the line in half at a junction box and measure each half. The faulty half shows the wrong impedance; split that half again, and keep going until you find the faulty speaker or section of cable. Disconnect the amplifier while you work.

Back to top