Before you start
Good background music is easy to miss: it fills the room evenly, sits comfortably under conversation and never draws attention to the loudspeakers. You should not be able to walk around the room and hear one speaker getting louder as you approach it, then a quiet patch, then the next speaker. Getting there depends far more on choosing the right type of loudspeaker, spacing them correctly and setting the level for the space than on the quality of any single box.
This guide covers background music for shops, restaurants, bars, cafés, hotels, offices, gyms and similar spaces:
- Survey the space and decide what the system needs to do.
- Choose the loudspeaker type: ceiling, surface or pendant.
- Space the loudspeakers so the coverage is even.
- Choose 100 V line or low impedance, and size the amplifier.
- Plan zones and volume control.
- EQ the system so it sounds natural at low level.
- Set the level for the type of space, and check it when the room is busy.
Survey the space
- The ceiling. Is it a suspended tile grid, plasterboard, concrete, or open to the roof with exposed ducts? How high is it? This largely decides which loudspeakers can be used.
- The layout. Note seating areas, counters, tills, kitchens, toilets, entrances and outside areas. Each may need its own level, or its own zone.
- The surfaces. Hard floors, glass, tiles and bare ceilings make a room lively and loud. Carpet, soft seating, curtains and acoustic panels calm it down. A lively room needs less level and more, smaller loudspeakers.
- The noise. Listen to the room when it is quiet and, ideally, when it is busy. Coffee machines, extraction, air conditioning and crowd noise set the level the music has to work with.
- What else the system does. Paging, announcements and fire alarm messages each change what the system needs (see zones and paging).
- The look. Find out what the client wants to see. Many interiors call for loudspeakers that disappear into the ceiling; others want visible, characterful pendants or surface speakers that match the décor.
Music licence: in the UK, a business playing recorded music in public, including background music in a shop, restaurant, office or gym, normally needs TheMusicLicence from PPL PRS. Check with PPL PRS for your premises.
Choose the loudspeaker type
| Type | Best for | Things to know |
|---|---|---|
| Ceiling (in-ceiling) | Suspended or plasterboard ceilings up to about 4 m high: shops, offices, restaurants, hotel corridors | Almost invisible and gives the most even coverage. Needs a ceiling void deep enough for the speaker and its back box. |
| Surface (wall or box) | Concrete or high ceilings, existing buildings, bars, gyms, outdoor areas | Easy to fit on walls, beams or ceilings, and usually goes louder and deeper than a ceiling speaker. More visible, and harder to make even in large rooms. |
| Pendant | Open or high ceilings, warehouses, industrial-style interiors, atriums and retail with exposed services | Hangs on a cable to bring the sound down to the listeners. Most spread sound widely downwards, often 180° or more. |
| Subwoofer | Bars, gyms, fashion retail and anywhere music needs weight | Small ceiling and surface speakers have limited bass. One or two subwoofers, often hidden in the ceiling void or under seating, fill this in. |
Ceiling speakers
- Size. 5 to 6.5 inch drivers suit most background music; 8 inch gives fuller sound in larger or higher rooms. Two-way models with a separate tweeter sound clearer than single-cone types.
- Back boxes. A sealed back can or box keeps sound from leaking into the ceiling void and neighbouring rooms, improves the bass and protects the speaker from dust. In a suspended ceiling, a back box is strongly recommended.
- Fire ratings. Where a speaker cuts through a fire-rated ceiling, use a fire-rated speaker or fit a fire dome over it so the ceiling keeps its fire resistance. Check with the building's fire strategy.
- Tile bridges. In suspended ceilings, support the speaker with a tile bridge or ceiling rail, so its weight is not hanging on the tile alone, and use a safety wire to the soffit.
- Damp areas. Bathrooms, pool areas and kitchens need speakers rated for humidity, with corrosion-resistant grilles.
Surface speakers
- Mount at about 2.2 to 3 m high, above head height but not so high that the sound skims over the listeners.
- Tilt them down 10 to 20° so they point at the far side of the area they cover, not at the opposite wall.
- Use the mounting brackets supplied or approved by the manufacturer, fixed into something solid, and add a safety wire or secondary fixing for anything over head height.
- Keep them out of corners and close to the ceiling only if you want more bass; both boost low frequencies and can make the sound boomy.
Pendant speakers
- Hang them so the speaker sits about 3 to 4 m above the floor in a high space, or a little below any lighting, ducts or beams that would block the sound.
- Keep every pendant at the same height so their coverage is even.
- Use the manufacturer's suspension kit, fixed to the structure, with a secondary safety wire. The cable must not carry the weight unless it is designed to.
- Keep pendants clear of lights, sprinkler heads and smoke detectors, and away from anything that sways or gets hot.
Understand coverage
A loudspeaker sends sound out in a cone. Its coverage angle (or dispersion) is the angle within which the level stays within a few dB of the level straight in front, usually 6 dB. Manufacturers quote it on the data sheet, often at 1 kHz or 2 kHz. Coverage narrows at higher frequencies, so a speaker that covers 120° at 1 kHz may only cover 60 to 90° at 4 kHz, where much of the clarity lives.
The diameter of the area covered at ear height is:
D = 2 × (h − e) × tan(θ ÷ 2)
where h is the speaker height, e is ear height (about 1.2 m seated or 1.6 m standing) and θ is the coverage angle. For a 90° speaker, tan(45°) = 1, so D is simply twice the height above the ears.
Low ceilings are hard work. In a 2.4 m ceiling over a standing audience, a 90° speaker is only 0.8 m above ear height and covers a circle just 1.6 m across. That means many speakers close together, each running quietly. A wider-dispersion speaker helps a lot in low rooms.
Lay out ceiling speakers
Ceiling speakers are usually laid out on a regular square grid. How far apart they go depends on how even the sound needs to be.
| Layout | Spacing between speakers | Level variation | Use it for |
|---|---|---|---|
| Edge to edge | D | Largest: quieter patches between speakers | Low-level background music where cost matters most, and corridors |
| Minimum overlap | D × 0.71 | Moderate: no gaps in coverage | Most background music, and paging |
| Full overlap | D × 0.5 | Smallest: very even | Speech clarity, voice alarm, premium foreground music, very low ceilings |
Worked example
A restaurant 12 m by 9 m with a 3 m ceiling, seated diners and 90° ceiling speakers:
- Height above ears: 3.0 − 1.2 = 1.8 m.
- Coverage diameter: D = 2 × 1.8 × 1 = 3.6 m.
- Minimum overlap spacing: 3.6 × 0.71 = 2.55 m.
- Along the 12 m length: 12 ÷ 2.55 = 4.7, so 5 speakers. Across the 9 m width: 9 ÷ 2.55 = 3.5, so 4 rows. That is 20 speakers.
- For lower-level music only, edge to edge at 3.6 m gives 4 × 3 = 12 speakers, at the cost of less even sound.
Place the first row half a spacing in from each wall (here about 1.3 m), so the coverage reaches the edges of the room without hitting the walls hard.
The Ceiling Speaker Layout Planner does this calculation for any room, including the speaker count and amplifier power, and the Speaker Coverage & SPL Calculator shows a level map of the layout.
Practical tips
- Line speakers up with the ceiling grid, lights and diffusers so they look planned. Small shifts of up to about 10% of the spacing make no audible difference.
- Do not put speakers directly over tills, reception desks or places where staff stand all day. Move them a little to one side, or use a lower tap.
- Keep them away from walls (at least half a spacing) to avoid strong reflections and a boomy sound near the wall.
- Where the ceiling height changes, recalculate the spacing for each area.
- In toilets, corridors and small rooms, one or two speakers on a lower tap are usually enough.
Lay out surface and pendant speakers
Surface speakers on walls
- Stagger them along opposite long walls, so each one fills the gap between two on the other side.
- Space them at roughly the width of the room for background music in a narrow space, or closer for even coverage. A typical spacing is 4 to 8 m.
- Do not rely on a pair at one end of a long room. The people nearest get too much, and the far end gets too little. More speakers at lower level always sounds better.
- Face them away from entrances, tills, staff positions, and windows or doors to neighbours.
- Mix in mono. Background music should be sent in mono, or with the stereo combined, so everyone hears the whole song whichever speaker is nearest.
Pendants
Pendants are laid out on a grid just like ceiling speakers, using the coverage formula with the height of the speaker (not the ceiling) above ear height. Because most pendants spread sound very widely, they can be spaced further apart than ceiling speakers at the same height. Use the manufacturer's quoted coverage angle; if it is 180° or more, work with about 120° to allow for the narrower coverage at higher frequencies.
For example, pendants hung at 4 m over a standing audience (1.6 m ears), using 120°: D = 2 × 2.4 × tan(60°) = 8.3 m, so minimum overlap spacing is about 5.9 m.
100 V line or low impedance
Background music systems with more than a handful of speakers almost always use a 100 V line system (70 V in some countries). Each speaker has a transformer with selectable taps (for example 1.5, 3 and 6 W), and all the speakers connect in parallel across one pair of cables from a 100 V amplifier.
| 100 V line | Low impedance (4 or 8 Ω) | |
|---|---|---|
| Number of speakers | Dozens on one amplifier channel | Usually 1 to 4 per channel |
| Cable runs | Long runs with thin cable | Short runs with thicker cable |
| Setting the level per speaker | Easy: change the tap | Not possible without extra hardware |
| Sound quality | Good; transformers limit the deepest bass | Best, with full bass |
| Typical use | Shops, offices, restaurants, hotels, paging | Bars, small premium spaces, subwoofers |
Choosing taps and the amplifier
- Choose a tap for each speaker. For background music, a low tap such as 1.5 or 3 W is usually plenty in a normal ceiling. Use higher taps for high ceilings, noisy areas and anywhere the system might also play louder music. Use lower taps in small rooms, toilets and near staff positions.
- Add up all the taps on each amplifier channel. Twenty speakers on 3 W taps is 60 W.
- Add at least 20 to 25% headroom: 60 × 1.25 = 75 W, so choose a 100 W, 100 V amplifier channel. Running an amplifier close to its full rating causes distortion and overheating.
- Size the cable for the total load and length, keeping power loss under about 10%.
- Check the polarity: connect every speaker the same way round (+ to +).
- Measure the line impedance with a 100 V line impedance meter before connecting the amplifier. It should be close to 10,000 ÷ total watts (here 10,000 ÷ 60 ≈ 167 Ω). A very low reading means a short circuit or a wrong tap.
Do not connect low-impedance speakers directly to a 100 V line, or the wrong tap (such as the 8 Ω bypass) of a transformer speaker. The amplifier sees a near short circuit and may shut down or be damaged. A 100 V line carries a hazardous voltage at full power, so make connections with the amplifier off.
The 100V / 70V Line Designer adds up the taps and checks the amplifier headroom and cable loss, the Speaker Cable Size Calculator sizes the cable, and the Speaker Impedance Calculator checks low-impedance wiring.
Zones, volume control and paging
A zone is an area that can have its own music source and level. Plan zones around how the space is used, not just the room plan:
- Typical zones: shop floor, changing rooms, restaurant, bar, terrace, toilets, back of house, gym floor and studios.
- Volume control in each zone lets staff adjust the level as the room fills and empties, without walking to the rack. Use 100 V attenuators or wall controllers from the amplifier or mixer, and set a maximum so the level cannot be turned up too far.
- Toilets and corridors usually work best as their own zone, a few dB quieter than the main area.
- Outdoor areas need their own zone, a lower maximum level, and speakers aimed away from neighbours.
- Automatic level control using an ambient noise sensor raises the music as the room gets busier and lowers it as it empties. It is well worth having in restaurants, bars and stations.
Paging and announcements
If the system is used for announcements, the microphone or message player should take priority and turn the music down automatically (often called ducking or muting). Paging needs more even coverage than music alone, so lean towards minimum overlap or full overlap spacing in areas where announcements must be understood.
Fire alarm and evacuation messages must use a voice alarm system designed, installed and maintained to the relevant standards (BS 5839-8 in the UK, with loudspeakers to BS EN 54-24). A background music system is not a voice alarm system unless it has been designed as one. Where music must mute when the fire alarm sounds, use an interface approved for the fire alarm system and a competent installer.
EQ for background music
Background music is played at low level, often through small speakers in rooms full of hard surfaces. EQ makes it sound full and natural without being boomy or harsh.
Start with the room
- Set all EQ flat, then play well-known, well-recorded music at the intended level.
- Walk the whole space, including near walls, in corners and under speakers, listening for boom, harshness and quiet patches. If you have a measurement microphone and analyser, measure with pink noise at several positions and average them, as described in How to Set Up Sound in a Room.
- Cut problems with gentle, wide filters of a few dB. Avoid boosting, which reduces headroom and stresses small speakers.
- Listen again at the level the room will actually run at, which is usually lower than you think.
Common adjustments
| Range | Problem | What to do |
|---|---|---|
| Below 60 to 100 Hz | Small speakers straining, rattling or distorting | Set a high-pass filter at about 80 to 100 Hz for 5 to 6.5 inch ceiling speakers, or at the speaker's lowest rated frequency. Leave the deep bass to subwoofers. |
| 100 to 250 Hz | Boomy, especially near walls and corners, or from surface speakers | Cut 2 to 4 dB with a wide filter. |
| 250 to 500 Hz | Muddy, boxy, crowded | A small cut helps in rooms with many speakers whose sound overlaps. |
| 2 to 5 kHz | Harsh or tiring, especially in hard rooms or close to speakers | Cut gently. Too much here makes music intrusive even at low level. |
| Above 8 kHz | Dull, lifeless | A gentle shelf boost adds air, especially for speakers mounted high or behind thick grilles. |
Sound at low levels
Our ears are less sensitive to bass and extreme treble at low listening levels, so music played quietly sounds thin. A gentle lift of a few dB at the low end (around 100 Hz, above the high-pass filter) and the top end (above 10 kHz) helps background music sound full at 55 to 65 dB(A). Some processors and amplifiers have a loudness or low-level EQ setting that does this automatically.
Subwoofers
- Cross over between the main speakers and the subwoofer at about 80 to 120 Hz, using the processor's crossover or the subwoofer's built-in filter.
- Place subwoofers near a wall or on the floor for more output, but check for boomy spots. Two subwoofers in different places usually give more even bass than one.
- Set the subwoofer level by ear, so it adds weight without being noticed as a separate source. If staff or neighbours notice the bass first, it is too loud.
- Align the subwoofer's timing with the main speakers using delay or its phase control. The Subwoofer Alignment Calculator helps.
Dynamics and the source
- Use gentle compression or a music levelling processor, so quiet tracks are not lost and loud tracks do not jump out.
- Use a limiter on each amplifier output to protect the speakers and cap the maximum level.
- Use a consistent source. Commercial background music services normalise the level of every track. If you build your own playlists, turn on volume normalisation in the player.
- Choose music for the space. Heavily bass-led or highly dynamic music needs a more capable system to play well at low level.
Set the level for the space
The right level depends on the type of space, the time of day and how busy it is. As a starting point, background music should be clearly audible but should not make anyone raise their voice: normal conversation at about a metre is roughly 55 to 65 dB(A). Measure with an SPL meter, set to A-weighting and a slow or Leq reading, at several places where people sit or stand.
| Space | Typical level, dB(A) | Notes |
|---|---|---|
| Spa, treatment rooms, library | 40 to 50 | Barely there; just enough to mask silence and nearby sounds. |
| Office, reception, waiting room | 45 to 55 | Also helps privacy by masking nearby conversations. |
| Hotel lobby, fine dining | 50 to 60 | Easy conversation across the table is the priority. |
| Café, casual restaurant, salon | 55 to 70 | Rises in the evening and as the room fills. |
| Supermarket, general retail | 60 to 70 | Even coverage matters more than level. Keep it lower near tills. |
| Fashion retail, showroom | 65 to 80 | Music is part of the brand, so it can be more prominent. |
| Pub or bar | 65 to 80 | Lower in the early evening, higher when busy. |
| Gym floor | 70 to 80 | Group exercise studios often run louder; see the warning below. |
These are typical ranges, not rules. The best check is to stand in the space when it is busy and ask: can I hear the music, and can I hold a normal conversation without straining? If customers lean in to talk or staff raise their voices, it is too loud.
Set the maximum level
- Play typical music through every zone with the zone volume controls at maximum.
- Adjust the amplifier or processor until the level at the listeners is the top of the range you want for that space.
- Lock that in with the processor's output limits or the amplifier's level controls, so the wall controls cannot exceed it.
- Set the normal operating level a few dB below the maximum, and show staff how to adjust it.
Protect staff hearing: under the Control of Noise at Work Regulations 2005, employers must act when staff are exposed to an average of 80 dB(A) over a working day, with further duties at 85 dB(A). Bar staff, gym instructors and retail staff under speakers all day can approach these levels, so measure where staff work, not just where customers are, and keep levels down near counters and tills.
Neighbours and licensing
Music can carry through walls, floors, windows and open doors. Premises licences often include noise conditions, such as keeping doors and windows closed or limiting levels at the boundary. Keep outdoor speakers low and pointing into the site, consider a limiter on outdoor zones, and listen outside after dark, when background noise drops and music is most noticeable.
Commission and hand over
- Every speaker working, on the right tap, and in polarity
- 100 V line impedance measured and recorded for each circuit
- No buzzes, rattles or distortion from speakers, grilles or ceiling tiles at maximum level
- EQ, high-pass filters and limiters set, and the system checked at the normal level
- Coverage walked: no hot spots under speakers and no dead patches
- Maximum level set for each zone, and levels measured at customer and staff positions
- Paging priority and fire alarm muting tested, if fitted
- Staff shown how to choose sources and set levels, with a simple written guide by the controls
- Settings backed up, and a drawing of speaker positions, zones, taps and amplifier channels left on site
Troubleshooting
| Problem | Likely causes | Things to try |
|---|---|---|
| Loud under each speaker, quiet between | Speakers too far apart, coverage too narrow, taps too high | Add speakers or use wider-dispersion models, lower the taps and raise the amplifier level. |
| One end of the room much louder | A few large speakers at one end, mismatched taps | Spread more speakers through the room and balance the taps. |
| Boomy sound | Speakers near walls or in corners, no high-pass filter, too much subwoofer | Cut 100 to 250 Hz, set a high-pass filter, move speakers out from corners and reduce the subwoofer. |
| Harsh or tiring sound | Too much 2 to 5 kHz, hard room, level too high, speakers aimed at listeners' heads at close range | Cut gently around 2 to 5 kHz, lower the level, re-aim or move speakers. |
| Thin sound | Speakers out of polarity, small speakers with no subwoofer, level very low | Check polarity, add low-level bass lift, or add a subwoofer. |
| Amplifier shuts down or clips | Taps add up to more than the amplifier's rating, a short circuit, low-impedance speaker on a 100 V line | Measure the line impedance, check every tap, split the load across more channels. |
| Hum or buzz | Ground loop between the music player and amplifier, unbalanced cable near mains | Use balanced connections or an isolation transformer, and power all the equipment from one supply point. |
| Rattles at certain notes | Loose ceiling tiles, grilles, back boxes or fittings | Play a slow sine wave sweep and find the rattle, then fix or pad it. |
| Staff keep turning it up or down | Room noise changes through the day, no maximum level set | Fit an ambient noise sensor, set limits, and agree levels for busy and quiet times. |