All guides
viewhub.stream · How-to Guides

Audio Basics: Equipment, Decibels and Sound Levels

What mixers, compressors, amplifiers and speakers do, how decibels and SPL work, and what else you need to know when starting out

24 min readUpdated

Contents

Before you start

Starting out in live sound, installation or AV can feel like learning a new language. People talk about gain, dBu, aux sends, DIs and wedges as if everyone knows what they mean. This guide explains the basics in plain English: what sound is, how decibels and sound levels work, what each piece of equipment in a sound system does, how it all connects, and the habits that keep you, the audience and the equipment safe.

You do not need to read it all at once. Use the contents list to jump to what you need, and come back as you meet new kit. Two other guides build on this one: How to Set Up Sound in a Room and How to Set Up Background Music.

The one idea to remember: every sound system is a chain. Sound goes in at one end (a microphone or a music player), is turned into an electrical signal, is adjusted and mixed, made more powerful, and comes out of loudspeakers at the other end. Once you know where each box sits in the chain, everything else makes sense.

What sound is

Sound is a vibration travelling through the air as tiny changes in air pressure. A guitar string, a voice or a loudspeaker cone moves back and forth, pushing and pulling the air next to it, and that pattern spreads outwards at about 343 metres per second (at 20 °C). When it reaches your ear, your eardrum vibrates in the same pattern and your brain hears it as sound.

Frequency

Frequency is how many times a second the vibration repeats, measured in hertz (Hz). Low frequencies sound deep (bass); high frequencies sound bright (treble). Young, healthy ears hear from about 20 Hz to 20,000 Hz (20 kHz). The top end falls with age and noise exposure.

The audio frequency range divided into bands, with where common sounds sit Sub-bassBassLow midsMidsUpper midsHighs20501002005001k2k5k10k20kFrequency (Hz)PianoBass guitarKick drumMale voiceFemale voiceCymbals
The audible range runs from about 20 Hz to 20 kHz. The grey bars show the approximate range of some common sounds, including their harmonics.
BandRangeWhat lives there
Sub-bass20 to 60 HzFelt more than heard: kick drum thump, bass synths, rumble
Bass60 to 250 HzBass guitar, the body of a kick drum, the warmth of male voices
Low mids250 to 500 HzFullness, and where mud and boxiness build up
Mids500 Hz to 2 kHzThe core of most instruments and voices
Upper mids2 to 5 kHzClarity and presence; the ear is most sensitive here
Highs5 to 20 kHzSibilance (s sounds), cymbals, air and sparkle

Wavelength

Each frequency has a wavelength: the distance the sound travels during one vibration. Wavelength = 343 ÷ frequency. A 50 Hz bass note is about 6.9 m long; a 5 kHz tone is about 7 cm. This is why bass spreads in all directions and goes through walls, while treble is easily blocked and beams in one direction. It is also why small speakers struggle with deep bass.

Octaves

Doubling a frequency raises it by one octave: 100 Hz to 200 Hz is one octave, and so is 5 kHz to 10 kHz. The audible range is about 10 octaves. Graphic equalisers are often divided into octaves or thirds of an octave, which is why their sliders are labelled 31, 63, 125, 250, 500 Hz, 1, 2, 4, 8 and 16 kHz.

Decibels explained

The decibel (dB) is the unit you will see everywhere: on faders, meters, speaker specifications and SPL meters. It is not a fixed amount like a metre. It is a way of comparing two levels on a scale that matches how we hear.

Why decibels?

Our ears cope with an enormous range: the loudest sound you can bear is about a million times greater in pressure than the quietest you can hear. Writing that in ordinary numbers is clumsy, and it does not match how we perceive loudness. Decibels use a logarithmic scale, which squeezes that huge range into roughly 0 to 130 and treats every equal step as an equal change in loudness.

The rules of thumb

ChangeWhat it means
+1 dBAbout the smallest change in level most people notice
+3 dBDouble the power. Clearly noticeable, but not twice as loud
+6 dBDouble the voltage or sound pressure. Also what you lose each time you double your distance from a single speaker outdoors
+10 dBTen times the power, and sounds roughly twice as loud
+20 dBA hundred times the power, ten times the voltage, sounds about four times as loud
−3 dB, −6 dB and so onThe same changes in the other direction

The surprising consequence: to make a system sound twice as loud, you need about ten times the amplifier power. Doubling the amplifier from 500 W to 1,000 W only gains 3 dB.

The formulas

For those who like the maths: a power ratio in dB is 10 × log₁₀(P₂ ÷ P₁), and a voltage or pressure ratio is 20 × log₁₀(V₂ ÷ V₁). The factor is 20 for voltage because power rises with the square of voltage. The dB Toolbox does these conversions for you.

dB with a reference

A plain "dB" is a change: "turn it up 3 dB". When a letter follows, the number is measured against a fixed reference, so it becomes an actual level:

UnitReference (0 dB)Where you see it
dB SPL20 micropascals, about the quietest sound a young person can hearSound level in the air: SPL meters, speaker specifications
dB(A), dB(C)dB SPL with a frequency weightingNoise measurements and hearing safety. A-weighting matches how we hear at moderate levels; C-weighting includes more bass and is used for loud music and peaks
dBu0.775 voltsProfessional analogue signal levels
dBV1 voltConsumer equipment and some microphone specifications
dBFSFull scale: the largest number a digital system can storeDigital mixers, interfaces and recordings. 0 dBFS is the maximum, so levels are negative, for example −18 dBFS
dBm1 milliwattRadio, telecoms and some older audio equipment
LUFSLoudness relative to digital full scaleLoudness of programmes and music for broadcast and streaming

Sound pressure level (SPL)

SPL is how loud a sound actually is in the air at a particular place, measured in dB SPL or, more often, dB(A). It is measured with an SPL meter (or sound level meter). Phone apps are fine for a rough idea; for anything that matters, such as hearing safety or noise limits, use a calibrated meter.

Typical sound levels from quiet to painful 0 dBThreshold of hearing20 dBRustling leaves, quiet studio30 dBWhisper, quiet bedroom40 dBLibrary, quiet office60 dBNormal conversation at 1 m70 dBBusy restaurant, vacuum cleaner85 dBHeavy traffic: 8-hour action level100 dBLoud concert, nightclub110 dBFront of a rock concert120 dBThreshold of discomfort130 dBThreshold of pain
Typical sound levels. Each 10 dB step sounds about twice as loud as the one below.

Distance: the inverse square law

Sound spreads out as it travels, so it gets quieter with distance. From a single loudspeaker in open space, the level drops by about 6 dB every time the distance doubles. If it is 100 dB at 1 m, it is about 94 dB at 2 m, 88 dB at 4 m and 82 dB at 8 m. Indoors, reflections from walls and ceilings keep the level up further from the speaker, so the drop is smaller. Line array systems, used at large events, lose less with distance, closer to 3 dB per doubling over part of their range.

Adding sources

Decibels do not add like ordinary numbers. Two equal sources together are 3 dB louder than one, not twice the number: two speakers each producing 90 dB give 93 dB. Ten equal sources give 10 dB more. If one source is 10 dB quieter than another, it adds almost nothing to the total.

How loud will a speaker go?

Speaker specifications give a sensitivity: the SPL it produces at 1 m with 1 watt, for example 95 dB (1 W, 1 m). From that you can estimate:

SPL at distance = sensitivity + 10 × log₁₀(watts) − 20 × log₁₀(metres)

For example, a 95 dB speaker given 100 W: 95 + 20 = 115 dB at 1 m. At 16 m away: 115 − 24 = 91 dB. Always check the speaker's maximum SPL too, as no speaker can go louder than that however much power it gets. The Speaker Coverage & SPL Calculator works this out for any speaker and distance.

Protect your hearing

Hearing damage is permanent and builds up over years. It usually starts as dull or muffled hearing, or ringing (tinnitus), after a loud event. Both are warnings.

Average levelTime before the daily dose reaches the 85 dB(A) action level
85 dB(A)8 hours
88 dB(A)4 hours
91 dB(A)2 hours
94 dB(A)1 hour
97 dB(A)30 minutes
100 dB(A)15 minutes

Every 3 dB increase halves the safe time. In the UK, the Control of Noise at Work Regulations 2005 require employers to act at a daily exposure of 80 dB(A) and to provide hearing protection and control the noise at 85 dB(A). Wear proper ear protection (musicians' earplugs keep the sound natural while reducing it) whenever you are near loud speakers, and take breaks in quieter areas.

Signal levels

Inside the cables, sound travels as a changing voltage. Different equipment works at very different voltages, and connecting the wrong level to the wrong input is one of the most common beginner mistakes.

LevelTypical voltageComes fromConnect to
Mic levelA few thousandths of a volt (about −60 to −40 dBu)Microphones, and DI box outputsA mic input with a preamp (XLR on a mixer)
Instrument levelTenths of a voltElectric guitars and basses with passive pickupsAn instrument (Hi-Z) input, or a DI box
Consumer line levelAbout 0.3 V (−10 dBV)Phones, laptops, TVs, hi-fi and DJ equipmentA line input, ideally through a DI box for long runs
Professional line levelAbout 1.2 V (+4 dBu)Mixer outputs, processors, interfacesLine inputs on processors, amplifiers and powered speakers
Speaker levelTens of volts, at high currentAmplifier outputsPassive loudspeakers only

Never connect an amplifier's speaker output to anything except a loudspeaker. Speaker level can destroy mixer inputs, processors, interfaces and headphones instantly, and at high power it can give you a shock. Equally, never plug a line-level source into a mic input with the gain turned up: it will be massively too loud.

Gain, level and headroom

  • Gain is amplification applied to bring a signal up to a useful working level, most importantly at the mixer's input (the preamp).
  • Nominal level is the normal working level a piece of equipment expects, such as +4 dBu.
  • Headroom is the space between the normal level and the point where the signal distorts (clips). Good headroom lets sudden loud sounds through cleanly.
  • Noise floor is the hiss and hum present even with no signal. The aim is to keep the signal well above the noise floor and well below clipping.
  • Clipping happens when a signal is pushed beyond what a stage can handle. The tops of the waveform are cut off, it sounds harsh and distorted, and it can damage speakers.

Setting every stage at a healthy level is called gain structure or gain staging. How to Set Up Sound in a Room walks through it, and the Microphone Gain Structure Calculator shows how much gain a microphone needs.

The signal chain

A typical live sound signal chain MicrophonesInstrumentsStage boxMixerProcessorAmplifierSpeakers mic levelvia DI boxesmulticoregain, EQ, mixEQ, delay, limitspeaker levelsound
Sources go into the stage box, down a multicore to the mixer, out through a speaker processor and amplifier to the loudspeakers. Powered speakers have the processor and amplifier built in.

A small system may have just a microphone, a mixer and two powered speakers. A large one adds stage boxes, monitor mixes, processors, many amplifiers and dozens of speakers, but the chain is the same. When something goes wrong, follow the signal from one end to the other until you find where it stops.

Microphones, DI boxes and stage boxes

Microphones

A microphone turns sound into a small electrical signal.

  • Dynamic microphones are tough, need no power, and handle very loud sounds. They are the standard for vocals, drums and guitar amplifiers on stage.
  • Condenser microphones are more sensitive and detailed. They need power, usually 48 V phantom power sent from the mixer down the microphone cable. Used for choirs, acoustic instruments, drum overheads and studio vocals.
  • Ribbon microphones are smooth-sounding and delicate, mainly used in studios. Some can be damaged by phantom power or a strong blast of air.
  • Polar pattern describes which directions a microphone hears. Cardioid (heart-shaped) microphones hear mostly from the front and reject sound from behind, which helps prevent feedback.

How to Set Up Sound in a Room covers choosing and positioning microphones in detail.

DI boxes

A DI box (direct injection) converts an instrument or consumer line signal into a balanced mic-level signal, so it can travel a long way down a microphone cable into a mixer's mic input without picking up noise. Use one for keyboards, bass guitars, acoustic guitars with pickups, laptops and phones.

  • Passive DIs use a transformer and need no power. Best for keyboards, laptops and active instruments.
  • Active DIs use electronics powered by phantom power or a battery. Best for passive guitar and bass pickups, which need a high input impedance.
  • Most DIs have a ground lift switch to cure hum caused by ground loops, and a pad to reduce very hot signals.

Stage boxes and multicores

Rather than running dozens of cables from the stage to the mixer, sources plug into a stage box on stage, connected to the mixer by one thick multicore cable (often called a snake). With digital mixers, the stage box usually contains the preamps and converters, and connects to the mixer with a single network or fibre cable.

The mixer

The mixer (also called a mixing desk, console or board) is the heart of the system. It takes many inputs, sets their levels and tone, blends them together, and sends different mixes to different places: the main speakers, stage monitors, recordings and streams.

The channel strip

Each input has a channel, and every channel has the same controls, in the order the signal passes through them:

The order of controls on a mixer channel GainHPFEQDynamicsAux (pre)FaderPanAux (post)sets input levelremoves rumbleshapes toneevens levelmonitor mixessets mix levelleft or righteffectsInput (mic or line) → … → main mix and buses
The signal passes through each control in turn. Aux sends can take the signal before the fader (pre-fade) or after it (post-fade).
ControlWhat it does
Gain (trim)Sets how much the preamp amplifies the input. The most important control on the desk: set it first, using the channel meter.
48 VSwitches phantom power on for condenser microphones and active DIs.
PadReduces a very loud input, often by 20 dB, before the preamp.
Polarity (Ø)Flips the signal upside down. Used when two microphones on one source cancel each other out.
High-pass filter (HPF)Removes low frequencies below a set point. Switch it on for anything that does not need deep bass.
EQAdjusts the tone by boosting or cutting bands of frequencies.
DynamicsOn digital mixers, a compressor and gate on every channel.
Aux sendsSend a separate amount of this channel to an extra mix, such as a monitor wedge or effects unit.
PanPlaces the channel between the left and right speakers.
MuteSilences the channel without changing its settings.
PFL / SoloLets you listen to just this channel in headphones and see its level on the main meters, without changing what the audience hears. PFL is pre-fade listen; AFL is after-fade listen.
FaderSets how much of the channel goes into the main mix. Aim to run important channels near 0 dB (unity).

Buses and outputs

  • Main mix (L/R or master): the mix that goes to the main speakers.
  • Aux or mix buses: extra mixes, built from the aux sends. Pre-fade sends are not affected by the channel fader, which suits monitor mixes for performers. Post-fade sends follow the fader, which suits effects like reverb.
  • Subgroups: combine several channels (all the drums, or all the vocals) into one bus with one fader and its own processing.
  • VCAs and DCAs: faders that remotely control the level of several channels at once without mixing them together. Handy for riding the level of a whole band or a group of presenters.
  • Matrix: extra outputs built from the main mix and buses, for feeds to delay speakers, other rooms, recording or a hearing loop.
  • Mute groups: mute or unmute many channels with one button.

Analogue and digital mixers

An analogue mixer has a physical knob for every control. A digital mixer converts the signals to numbers and offers far more processing in a smaller space: EQ and dynamics on every channel, built-in effects, recall of complete settings (scenes), remote control from a tablet, and connection to digital stage boxes. Most new installations and many events now use digital mixers.

Processing: EQ, dynamics and effects

Equalisers (EQ)

An equaliser boosts or cuts chosen frequencies to change the tone.

  • Graphic EQ: a row of sliders, each controlling a fixed band (often 31 bands, a third of an octave each). The slider positions draw a picture of the curve. Traditionally used on outputs to correct speakers and rooms.
  • Parametric EQ: each band has three settings: frequency (where), gain (how much boost or cut) and Q or bandwidth (how wide). More precise than a graphic.
  • Shelving EQ boosts or cuts everything above or below a point, like the bass and treble controls on a hi-fi.
  • High-pass and low-pass filters remove everything below or above a point.

A good habit: cut what you don't want before boosting what you do. Boosting raises the level, reduces headroom and makes feedback more likely.

Compressors

A compressor automatically turns down a signal when it gets louder than a set level, evening out the difference between quiet and loud. It makes a voice easier to hear consistently and a bass guitar sit steadily in the mix.

A compressor's input to output curve with a threshold and 4:1 ratio -40-40-30-30-20-20-10-1000Threshold −20 dB1:1, no compression4:1Input level (dB)Output level (dB)Example, 4:1 ratioInput −28 dB: below threshold, out at −28 dBInput −12 dB: 8 dB over, out at −18 dBInput 0 dB: 20 dB over, out at −15 dBGain reduction at 0 dB input: 15 dB
Below the threshold the signal passes unchanged. Above it, with a 4:1 ratio, every 4 dB of extra input gives only 1 dB more output.
ControlWhat it does
ThresholdThe level above which the compressor starts turning the signal down.
RatioHow hard it turns down. At 4:1, a signal 8 dB over the threshold comes out only 2 dB over.
AttackHow quickly it reacts once the signal goes over the threshold. Fast attack catches peaks; slower attack lets the start of each note through, keeping punch.
ReleaseHow quickly it lets go once the signal falls back.
KneeHard knee starts compressing abruptly at the threshold; soft knee eases in, sounding more natural.
Make-up gainTurns the whole signal back up to make up for the level the compressor took away.
Gain reduction meterShows how many dB the compressor is turning the signal down right now.

Other dynamics processors

  • Limiter: a compressor with a very high ratio, acting as a ceiling the signal cannot pass. Used to protect speakers and keep within noise limits.
  • Noise gate: mutes a channel when its level falls below a threshold. Used on drum microphones to cut out spill from other drums between hits.
  • Expander: a gentler gate that turns quiet signals down rather than muting them.
  • De-esser: turns down harsh "s" sounds in a voice.
  • Automatic mixer: for meetings and panels, it turns down microphones nobody is speaking into, so fewer are open at once.

Effects

  • Reverb simulates the reflections of a room or hall, making dry sounds feel more natural and spacious.
  • Delay repeats the sound after a set time, from a short slap-back to long echoes.
  • Chorus, flanger and modulation effects thicken or swirl the sound, mostly for instruments.
  • Pitch correction nudges notes into tune.

Effects are usually fed from post-fade aux sends, and the effect's output comes back into the mixer on its own channel (a return), so it can be blended in.

Loudspeaker processors

A loudspeaker management processor (or system processor) sits between the mixer and the amplifiers. It holds the settings that make the speakers sound right and stay safe:

  • Crossover: splits the signal into frequency ranges, sending bass to subwoofers and the rest to the main speakers, or low and high frequencies to separate drivers.
  • System EQ: corrects the speakers' response and the room.
  • Delay: time-aligns speakers at different distances.
  • Limiters: protect the speakers from too much power.

Powered speakers and many modern amplifiers have this processing built in.

Amplifiers

An amplifier (or power amp) takes the line-level signal from the mixer or processor and makes it powerful enough to move a loudspeaker's cone.

Matching amplifiers and speakers

  • Impedance is the speaker's resistance to the amplifier's current, measured in ohms (Ω): usually 4, 8 or 16 Ω. Every amplifier has a minimum impedance it can drive safely.
  • Wiring speakers together changes the impedance. Two 8 Ω speakers in parallel make 4 Ω; in series they make 16 Ω. Going below the amplifier's minimum makes it overheat or shut down. The Speaker Impedance Calculator works it out.
  • Power ratings. Choose an amplifier with around 1.5 to 2 times the speaker's continuous (RMS or AES) power rating, at the speaker's impedance. The headroom lets peaks through cleanly. An underpowered amplifier pushed into clipping is more likely to damage speakers than a more powerful one used sensibly.
  • Bridging combines the two channels of a stereo amplifier into one more powerful channel. Check the minimum impedance in bridge mode, which is usually higher.

Types of amplifier

  • Class D amplifiers are light, efficient and run cool. They are now the norm for live sound and installations.
  • Class AB amplifiers are heavier and less efficient, and are found in older and some hi-fi equipment.
  • 100 V line (or 70 V) amplifiers drive many transformer-equipped speakers on long cable runs, used for background music and paging. See How to Set Up Background Music.
  • Powered (active) speakers have the amplifier and processor built in: you send them a line-level signal and plug them into the mains.

Amplifier controls and lights

  • The input level (attenuator) controls on the front set the amplifier's sensitivity. Many engineers set them fully up and control the level from the mixer or processor, so the whole system is set up consistently.
  • Signal lights show a signal is present. Clip or limit lights show it is at or beyond its maximum: if they light more than very occasionally, turn down.
  • Protect lights show the amplifier has shut down to protect itself, often from overheating, a short circuit or too low an impedance.

Loudspeakers

A loudspeaker turns the electrical signal back into sound. Inside are one or more drivers: a woofer for low frequencies, a midrange driver in some designs, and a tweeter or compression driver for high frequencies.

TypeWhat it is for
Full-range (top or main)Covers most of the audible range, from the bass to the treble. The main speakers that face the audience.
SubwooferReproduces only the deep bass, below about 80 to 120 Hz.
Monitor (wedge)A speaker on the stage floor facing the performers, so they can hear themselves and each other.
In-ear monitor (IEM)Earphones, usually wireless, giving performers their own mix with no wedge on stage. Quieter on stage and less prone to feedback.
Line arraySeveral boxes hung in a curved column, working together to throw sound evenly over long distances. Used at large venues and festivals.
ColumnA tall, slim speaker with many small drivers, giving a controlled vertical spread. Good for speech in reverberant rooms such as churches.
Ceiling, surface and pendantInstalled speakers for background music and paging.
  • Passive speakers need a separate amplifier and are connected with speaker cable.
  • Active or powered speakers have an amplifier built in and take a line-level signal plus mains power.

Digital and networked audio

Digital audio basics

  • Sample rate is how many times a second the signal is measured. 48 kHz is the standard for live sound, video and broadcast; 44.1 kHz for music; 96 kHz in some high-end systems.
  • Bit depth is how precisely each sample is measured. 24-bit gives a huge dynamic range and is standard for professional audio.
  • Latency is the delay through digital equipment. A few milliseconds is normal and unnoticeable; it becomes a problem when it adds up through many devices, especially for performers on in-ear monitors.
  • Clock: all digital devices passing audio between them must run at the same sample rate, locked to one master clock. Mismatched clocks cause clicks and dropouts.

Networked audio

Many systems now send audio over ordinary computer network cables. Dante is the most common system, carrying dozens or hundreds of channels on one Ethernet cable between stage boxes, mixers, processors, amplifiers and recorders. AES67 is an open standard that lets different brands talk to each other, and AVB/Milan is another approach used by some manufacturers. Networked audio needs a properly set-up network: use the switches and settings the manufacturer recommends, and keep audio separate from busy office networks. The Network Audio Bandwidth Calculator estimates the network load.

Cables and connectors

ConnectorUsed for
XLR (3-pin)Microphones and balanced line signals. Pin 1 is the screen, pin 2 hot (+), pin 3 cold (−). Also used for AES/EBU digital audio and DMX lighting with different cable
6.35 mm (¼ inch) jack, TRSBalanced line signals and stereo headphones. Has a tip, ring and sleeve, with two insulating bands on the plug
6.35 mm jack, TSUnbalanced instrument cables (guitar leads). Has only a tip and sleeve, with one insulating band on the plug
3.5 mm jackPhones, laptops and consumer equipment
RCA (phono)Consumer and DJ equipment, unbalanced
SpeakonSpeaker cables between amplifiers and passive speakers. Locks in place and keeps fingers away from the contacts
Binding posts and terminalsSpeaker connections on installed amplifiers and speakers
RJ45 and etherCONNetwork audio (Dante), digital stage boxes and control. etherCON is a rugged, locking version for touring
Phoenix (Euroblock)Screw terminal connectors for balanced audio and control in installed equipment
Powercon and IECMains power into equipment

Balanced and unbalanced

A balanced cable carries the signal twice, once normal and once upside down, on two wires inside a screen. Any interference picked up along the cable affects both wires equally. At the far end, the input flips the second copy back and combines them: the signal adds up, while the interference cancels out. That is why balanced cables (XLR, TRS) can run 100 m or more quietly, while unbalanced cables (TS jack, RCA) should be kept short, ideally under 5 m.

How a balanced cable cancels interference Signal sentNoise picked up on the wayAt the inputHot (+)Cold (−), flippedsame noise on both wiressame noise on both wiresCold flipped back and added:signal doubles, noise cancels
Noise picked up along a balanced cable arrives the same on both wires. When the input flips one copy back and adds them, the signal doubles and the noise cancels.

Cable care

  • Use speaker cable for speakers. Instrument and microphone cables are far too thin for amplifier power and can overheat. The Speaker Cable Size Calculator shows the size you need.
  • Coil cables over-under, alternating the direction of each loop, so they lie flat and uncoil without twisting. Never wrap them round your elbow.
  • Label both ends of every cable, and keep spares of every type.
  • Run cables tidily and tape them down or use cable ramps across walkways.
  • Keep audio cables away from mains cables and lighting dimmers. Where they must cross, cross at right angles.

Reading specification sheets

SpecificationWhat it tells you
Frequency responseThe range of frequencies reproduced, ideally with a tolerance, for example 50 Hz to 20 kHz ±3 dB. Without the tolerance, the figures mean little.
SensitivityFor a speaker, the SPL at 1 m with 1 W. Each 3 dB higher means half the amplifier power for the same level. For a microphone, how much signal it produces for a given sound.
Maximum SPLThe loudest the speaker can play, usually as a peak figure. Continuous levels are typically about 6 dB lower.
Power handlingHow much power a speaker can take. Continuous (RMS or AES) is the useful figure; programme is usually twice that and peak four times. Compare like with like.
ImpedanceThe load the speaker presents to an amplifier, such as 8 Ω.
Coverage or dispersionHow wide and tall the speaker spreads its sound, for example 90° × 60°.
THDTotal harmonic distortion: how much the equipment changes the signal. Lower is better.
Signal-to-noise ratioHow far the normal signal sits above the background hiss, in dB. Higher is better.
Dynamic rangeThe range between the noise floor and the maximum level, in dB.
LatencyThe delay through digital equipment, in milliseconds.

Good habits

  1. Power up in order: sources and mixer first, then processors, and amplifiers or powered speakers last. Power down in reverse.
  2. Mute or pull down before plugging in, and before switching phantom power on or off. A loud pop can damage speakers and startle everyone.
  3. Set gain first, then use faders to mix. Keep faders for important channels near 0 dB.
  4. Listen on headphones (PFL or solo) before sending a channel to the speakers.
  5. Start quiet and bring it up. It is much easier to turn a system up than to recover from blasting the audience.
  6. Watch the meters and the clip lights at every stage.
  7. Change one thing at a time when fault-finding, and follow the signal chain.
  8. Save and label settings, scenes and presets, and keep notes for next time.
  9. Ask. Experienced crew would much rather answer a question than fix a mistake.

Staying safe

  • Hearing: wear ear protection around loud systems, measure levels, and take quiet breaks.
  • Electrical safety: use equipment that is tested and in good condition, power it from RCD-protected supplies, never remove a mains earth, and leave temporary power distribution to competent people. Do not use equipment with damaged cables or plugs.
  • Manual handling: speakers, amplifier racks and cable drums are heavy. Lift with your legs, use trolleys and team lifts, and wear safety boots.
  • Working at height and rigging: only trained, competent people should hang speakers or work at height, using rated fixings and safety wires, and only from points approved for the load.
  • Trip hazards: tape down or cover every cable across a walkway.
  • Know the venue's rules: emergency exits, fire procedures, load-in routes and who is in charge.

Jargon buster

TermMeaning
FOHFront of house: the main audience sound, and the mixing position in the audience.
Monitors, foldbackSound sent to the performers on stage, through wedges or in-ear monitors.
WedgeA floor monitor speaker, named for its shape.
Line checkChecking each input works and arrives on the right channel, before the soundcheck.
SoundcheckSetting levels and tone with the performers before the event.
Ring outFinding and cutting the frequencies that cause feedback before the event.
FeedbackThe howl when a microphone picks up its own sound from a speaker in a loop.
Spill (bleed)Sound from other sources picked up by a microphone.
PatchWhich input or output is connected to which channel. "Patch the laptop to channel 12."
Tie lineA permanent cable between two places in a venue, such as the stage and the control room.
Unity0 dB on a fader or control: no boost and no cut.
HotA signal that is too loud, or the positive wire in a balanced cable.
Polarity and phasePolarity is a signal flipped upside down. Phase describes timing differences between signals. Both can cause cancellation when signals combine.
Comb filteringThe thin, hollow sound caused when the same sound arrives twice with a small delay.
Pink noiseA test signal with equal energy in every octave, used to measure and set up systems.
RTAReal-time analyser: shows the level of each frequency band on screen.
Scene, snapshotA saved set of settings on a digital mixer.
Stage left, stage rightLeft and right from the performer's point of view, facing the audience. House left and right are from the audience's view.
Upstage, downstageUpstage is the back of the stage, away from the audience; downstage is the front.
Get-in, get-outBringing equipment into and out of the venue (also load-in and load-out).
Back to top