All guides
viewhub.stream · How-to Guides

Audio Signals and Connectors Compared

Signal levels and voltages, balanced and unbalanced, digital formats, connectors, cable lengths and common wiring such as TRS to XLR

10 min readUpdated

Contents

Before you start

Audio travels between equipment in many forms: tiny microphone signals, instrument signals, consumer and professional line levels, powerful speaker signals, and digital formats on copper, coaxial, optical and network cables. Each has its own voltage, impedance, connectors and cable length limits. Plugging the wrong level into the wrong input, or wiring an adaptor incorrectly, causes hum, distortion, very quiet or very loud signals, and sometimes damage. This guide compares the common audio signals and connectors, gives typical cable lengths, and shows how to wire the adaptors and cables you use every day.

Cable lengths are typical, not guaranteed. They depend on the cable quality, the equipment at each end and the electrical environment. Test long runs before relying on them.

Signal levels and voltages

Analogue audio levels are usually given in dBu (0 dBu = 0.775 V) or dBV (0 dBV = 1 V). Every 6 dB doubles the voltage; every 20 dB multiplies it by ten.

Audio signal levels from microphone to speaker level, with voltages -60 dBu0.8 mV-40 dBu7.8 mV-20 dBu78 mV0 dBu0.78 V+20 dBu7.8 V+40 dBu78 VMicrophoneInstrumentConsumer line (−10 dBV)Professional line (+4 dBu)Line peaks / headroomSpeaker, 100 W into 8 ΩSpeaker, 1,000 W into 4 Ω
Typical working levels, from microphones (thousandths of a volt) to amplifier outputs (tens of volts). Each step up the scale is about ten times the voltage.
LevelTypical nominal levelVoltage (RMS)SourceDestination
MicrophoneAbout −60 to −20 dBuAbout 0.8 mV to 80 mVMicrophones, DI box outputsMic input with preamp
InstrumentAbout −20 to 0 dBuAbout 0.1 to 0.8 VGuitars and basses with passive pickupsInstrument (Hi-Z) input or DI box
Consumer line−10 dBV (−7.8 dBu)0.316 VPhones, laptops, hi-fi, DJ and consumer equipmentLine input
Professional line+4 dBu1.23 VMixers, processors, interfacesLine input, amplifier, powered speaker
Maximum line level+18 to +24 dBu6.2 to 12.3 VPeaks from professional equipmentThe headroom before clipping
HeadphoneVariesUp to a few voltsHeadphone amplifiersHeadphones only
Speaker (low impedance)Depends on powerAbout 28 V for 100 W into 8 Ω; 63 V for 1,000 W into 4 ΩPower amplifiersPassive loudspeakers only
100 V line100 V at full power100 V100 V line amplifiersTransformer speakers only

Speaker voltage is √(power × impedance). The dB Toolbox converts between dBu, dBV and volts, and Audio Basics explains decibels.

Speaker outputs carry dangerous voltages on large amplifiers and 100 V lines. Never connect an amplifier output to anything except loudspeakers, and make connections with the amplifier off or muted.

Impedance and matching

In modern audio, outputs have a low impedance and inputs a high impedance, typically at least ten times higher (called bridging). This passes the voltage across with almost no loss, and lets one output feed several inputs.

ConnectionTypical output impedanceTypical input impedance
Microphone to preampAbout 150 to 600 ΩAbout 1 to 3 kΩ
Passive guitar to instrument inputSeveral kΩ, rising with frequencyAbout 1 MΩ (Hi-Z)
Line output to line inputAbout 50 to 600 ΩAbout 10 kΩ or more
Amplifier to speakerA fraction of an ohm4, 8 or 16 Ω (the speaker)
  • Passive guitars need a high-impedance input. Plugged into a normal line input, they sound thin and dull. Use an instrument input or an active DI box.
  • Speakers are the exception: amplifiers must see a speaker load within their rating. See Audio Basics and the Speaker Impedance Calculator.
  • Digital audio uses cables of a specific impedance (110 Ω for AES3, 75 Ω for S/PDIF coax and MADI). Using the wrong cable causes errors over long runs.

Balanced and unbalanced

A balanced connection uses two signal wires (hot and cold) plus a screen. Any noise picked up along the cable is the same on both wires; the balanced input rejects what is common to both, keeping the signal and removing the noise. An unbalanced connection uses one signal wire and the screen, so noise picked up along the way is heard along with the signal.

BalancedUnbalanced
ConnectorsXLR, TRS jack, Euroblock, TT/BantamTS jack, RCA phono, 3.5 mm jack
Typical useMicrophones, professional line connections, long runsInstruments, consumer equipment, short connections
Typical reliable length100 m or moreAbout 5 to 10 m for line level; about 6 m for passive instruments
Noise rejectionGoodPoor; prone to hum and interference

Long unbalanced instrument cables also lose treble, because the cable's capacitance combines with the guitar's high impedance to act as a filter. Keep them short, or use a DI box near the instrument.

Audio formats compared

FormatTypeChannelsConnector and cableTypical maximum length
Balanced analogue (mic or line)Analogue1 per cableXLR, TRS, Euroblock; twisted-pair screened cable100 m or more
Unbalanced analogueAnalogue1 or 2TS, RCA, 3.5 mmAbout 5 to 10 m
Speaker levelAnalogue1 per pairSpeakon, binding posts, terminals; speaker cableDepends on cable size and impedance
100 V lineAnalogue1 per lineTerminals; two-core cableHundreds of metres, sized for loss
AES3 (AES/EBU)Digital2XLR, 110 Ω digital cableAbout 100 m
AES-3idDigital2BNC, 75 Ω coaxUp to about 1,000 m
S/PDIF coaxialDigital2 (or compressed surround)RCA, 75 Ω coaxAbout 10 m
S/PDIF optical (TOSLINK)Digital2 (or compressed surround)TOSLINK opticalAbout 5 to 10 m
ADATDigital8 at 48 kHzTOSLINK opticalAbout 5 to 10 m
MADIDigitalUp to 64BNC 75 Ω coax, or fibreAbout 100 m on coax; about 2 km on multimode fibre
Dante, AES67, AVBDigital networkDozens to hundredsRJ45 or etherCON on Cat5e or Cat6, or fibre100 m per copper link; kilometres on fibre
USB audioDigital2 to dozensUSBAbout 5 m (longer with active extenders)
HDMI and SDI embedded audioDigitalUp to 8 (HDMI) or 16 (SDI)HDMI or BNCAs the video signal
  • Clocking: digital audio devices must share the same sample rate and clock. A master clock, or the network clock in Dante, keeps them locked; otherwise you hear clicks and dropouts.
  • Networked audio is now the usual way to carry many channels around a building or event. The Network Audio Bandwidth Calculator estimates the load, and Audio Basics explains the basics.

Connectors and pinouts

XLR, TRS and TS connector pinouts, and Speakon NL4 contacts 123XLR 3-pin1 screen · 2 hot · 3 coldpin numbers are marked on the connectorSleeveRingTipTRS jackbalanced: tip hot, ring cold, sleeve screenSleeveTipTS jackunbalanced: tip signal, sleeve ground1+1−2+2−Speakon NL41± one speaker or low frequencies2± second channel or highs
XLR: pin 1 screen, pin 2 hot, pin 3 cold (the numbers are moulded next to each pin). Jacks are named by their segments: tip, ring and sleeve. Speakon NL4 has four contacts for one or two speaker channels.
ConnectorWiringUsed for
XLR 3-pin1 screen (ground), 2 hot (+), 3 cold (−)Microphones, balanced line, AES3 digital (with 110 Ω cable)
6.35 mm TRS jack (balanced)Tip hot, ring cold, sleeve screenBalanced line inputs and outputs, patch bays
6.35 mm TRS jack (stereo)Tip left, ring right, sleeve groundHeadphones, stereo unbalanced
6.35 mm TRS jack (insert)Tip send, ring return, sleeve ground (on most mixers)Mixer insert points
6.35 mm TS jackTip signal, sleeve groundInstruments, unbalanced line, effects pedals
3.5 mm TRSTip left, ring right, sleeve groundPhones, laptops, consumer equipment
3.5 mm TRRSTip left, ring 1 right, ring 2 ground, sleeve microphone (the common CTIA standard)Phone and laptop headsets
RCA (phono)Centre signal, outer ground; red right, white or black leftConsumer and DJ equipment, S/PDIF coax
Speakon NL2 and NL41+ and 1− for one speaker; 2+ and 2− for a second channel or bi-ampingAmplifier to passive speakers
Euroblock (Phoenix)+, −, ground (often marked with symbols)Balanced audio on installed equipment
Mini XLR (TA4F)Varies by manufacturerLavalier and headset microphones on bodypacks
TT (Bantam)Tip hot, ring cold, sleeve screenStudio patch bays
BNCCentre and shell, 75 ΩWord clock, MADI, AES-3id
RJ45 and etherCONStandard network wiringDante, AES67, AVB and digital stage boxes

XLR 5-pin is not for audio. 5-pin XLR is the standard for DMX lighting control. 3-pin XLR is sometimes used for DMX too, but DMX needs 110 Ω data cable, not microphone cable.

Common wiring

Wiring for TRS to XLR and TS to XLR cables TRS to XLR (balanced)TipRingSleevePin 1 (screen)Pin 2 (hot)Pin 3 (cold)TS to XLR inputTipSleevePin 1 (screen)Pin 2 (hot)Pin 3 (cold)pins 1 and 3 linked at the XLR
Left: a balanced TRS to XLR cable. Right: an unbalanced TS jack to a balanced XLR input, with pins 1 and 3 linked at the XLR.
Cable or adaptorWiringNotes
XLR female to XLR malePin 1 to 1, 2 to 2, 3 to 3The standard microphone and balanced line cable.
TRS jack to XLR (balanced)Tip to pin 2, ring to pin 3, sleeve to pin 1Connects balanced jack outputs and inputs to XLR.
TS jack (unbalanced output) to XLR (balanced input)Tip to pin 2, sleeve to pins 1 and 3 (link 1 and 3 at the XLR)Works, but keep it short. A DI box is better for long runs.
XLR (balanced output) to TS jack (unbalanced input)Pin 2 to tip, pin 1 to sleeve; pin 3 to sleeve for most outputsSome outputs prefer pin 3 left unconnected; check the equipment manual. Expect about 6 dB less level with some outputs.
3.5 mm stereo to 2 × RCATip to left (white), ring to right (red), sleeve to both screensThe usual phone or laptop to hi-fi lead.
3.5 mm stereo to 2 × TS jack or XLRTip to left, ring to right, sleeve to groundsUnbalanced; for anything but short runs, use a stereo DI box.
RCA to XLRCentre to pin 2, outer to pins 1 and 3Consumer level into a professional input; a DI box or line converter is better.
Insert Y cableTRS tip to the "send" TS jack, ring to the "return" TS jack, sleeve to both screensCheck the mixer manual: a few use ring as send.
Euroblock to XLR+ to pin 2, − to pin 3, ground to pin 1Balanced; for installed equipment.
Speakon NL4 to speaker1+ and 1− to the speaker's + and −For bi-amped speakers, 1± drives the low frequencies and 2± the highs; check the speaker.

Wiring tips

  • Keep polarity consistent: pin 2 is hot in modern equipment (the international standard). A cable with 2 and 3 swapped flips the polarity, which thins the sound where it mixes with other sources.
  • Connect the screen at both ends in normal cables. Lifting the screen at one end (a "telescopic shield") can cure some ground loops on line-level runs, but never on microphone cables, which need pin 1 to carry phantom power.
  • Use proper cable: twisted-pair screened cable for balanced audio, 110 Ω cable for AES3 and DMX, and 75 Ω coax for S/PDIF, MADI and word clock.
  • Test every cable you make with a cable tester before use, and label it.

Interfacing different levels

ProblemToolWhat it does
Instrument, laptop or phone into a mic input over a long cableDI boxConverts unbalanced high-impedance or line signals to balanced mic level, with a ground lift switch.
Consumer −10 dBV equipment into professional +4 dBu equipment (or the reverse)Line level converterMatches the levels and balances or unbalances the signal.
Hum from a ground loopAudio isolation transformer, or a DI box with ground liftBreaks the audio ground path without touching the mains earth.
Signal too hot for an inputPad or in-line attenuator (−10, −20 or −30 dB)Reduces the level before the input.
One microphone to two mixers (front of house and monitors, or broadcast)Microphone splitterSplits the signal safely, with transformer isolation on the second output.
Speaker output into a line input (for example, a car stereo or old amplifier into a mixer)Speaker-to-line converter (high-level input adaptor)Reduces the speaker signal to line level safely. Never connect a speaker output directly to a line input.

Never remove the mains earth to cure hum. Use balanced connections, DI boxes and isolation transformers instead. See Electrical Safety for AV and Events.

Cable lengths compared

Typical maximum cable lengths for each audio format 1 m10 m100 m1 km10 kmPassive instrument (unbalanced)Unbalanced line (RCA, TS)S/PDIF coaxTOSLINK / ADAT opticalUSB audioBalanced analogue (XLR)AES3 on 110 Ω cableDante / AES67 on Cat6MADI on 75 Ω coaxAES-3id on 75 Ω coaxMADI on multimode fibreDante on single-mode fibre
Typical reliable lengths on suitable cable, on a logarithmic scale.

Speaker cable length depends on the cable size, the speaker impedance and how much power you can afford to lose: see the Speaker Cable Size Calculator.

Choosing the right connection

SituationUsually best
Microphones to a mixer or stage boxBalanced XLR
Mixer to amplifiers, powered speakers or processorsBalanced XLR or TRS
Guitar, bass or keyboard to a mixer more than a few metres awayDI box, then balanced XLR
Laptop or phone to a PAStereo DI box, or a USB audio interface
Two digital devices, a stereo pairAES3 on XLR, or S/PDIF for short consumer links
Many channels between stage and mixerDigital stage box on network or fibre, Dante or MADI
Installed audio between rooms or across a buildingDante or AES67 on the network, or balanced analogue
Amplifier to passive speakers on stageSpeakon with suitably sized speaker cable
Background music across a building100 V line
Back to top